abus granit detecto x plus 8000 3d models

For screws, I used M2 (2mm dia) x 4mm long Philips head screws; any small 2mm screw would work between 4-6mm long, or a small tapping screw. The handle may be stiff initially; work the handle a few times and it will bed in and loosen up. ... PARTS...

One M5 x 30mm screw, you could go shorter or longer. You are smart and can figure this part out on your own I would venture to say. Watch the video for assembly, but if you are indeed smart you won't need to. Alternatively you can use a 8mm shaft...

Befestigungsmaterial: - 1x Gewindestande M3 x 85mm (oder Sechskantschraube unbedingt mit durchgängigen Gewinde) - 1x M3 Mutter zum Einschmelzen in Innen_vxxx.stl - 1x M3 Nylock-Mutter - 1x M3 Mutter - 1x M3x14 Schraube Unbedingt die...

I have also included a flat bottomed o-ring which you would be able to print in flexible filament. I've included 2 ways of making the ball, one which prints in two parts and screws together with a single M3 x 20mm screw, and one which prints without...

That way, they can travel over the case rather than behind it, allowing the printer to be pushed back closer to a wall.I had a few additional design goals:not require removing bed to add or remove the strain relief bracketnot interfere with Z endstop...

All parts can also be printed on a small print bed (120mm x 120mm) as well!If you print with PLA or other non-ABS materials please let me know if my part sizes are okay with your material. I can't print with anything but ABS so I can't test common...

For load-bearing parts like belt tensioners, you might want to go to 60-80% infill and/or higher extruder temperature.I ended up printing the spoolholder nut scaled 101% on X and Y so it'd spin onto the axle somewhat freely. 102% might be even...

1x - 3/8-16 x 1" socket head cap screw - This is the clamp screw. 1/4" hex "Allen" drive. Note that a 3/4" long screw will work, but ONLY FOR THE 250Tube (1-1/4" buffer). 1x - 3/8-16 nylock nut - Retains the clamp screw. I recommend printing the...

Since the electronics inside were fine I decided to 3d print a new housing for them. I made 2 versions because I had 2 versions of the controller mainly differing in the battery holders.  The two parts are held together by one m1.6 x...

I recommend scuffing the outside of the drawtube with 350 or finer grit to minimize reflections and improve motion. See photos for assembly. You will only need 4 3D Printed components for this focuser:1 Main Body-Hadley-focuser2 Turn Knob...

Lundy is a small island off the coast of Devon: https://www.landmarktrust.org.uk/lundyisland/ .The model uses LIDAR Point Cloud Data, which is very detailed and also has x,y and z to scale. I created this model using point cloud data as I was unhappy...

To add further weight there is a 5.5 knock out hole in the lid which will allow for a M5 x 8mm bolt to be bolted through to the nut. The lid is an interference fit but a couple of spots of superglue will add to the longevity of the fix. Any series of...

There was one solution out there that was for a CR-6 that was close and supposed to be usable on an SE, but it didn’t activate the x-axis stop sensor causing all sorts of problems requiring firmware modifications. The final design I came up with...

I've designed it in FreeCAD, and printed on my Anycubic Mega X. The instrument is bulky, but plays surprisingly nice. Construction is not perfect, I'm planning to go for next version if it will be interesting for someone besides me. Instructions,...

Movement: Head: uses two standard-sized servos Wheels: uses 6 x 120rpm worm gear 12v motors Credits: The DIN files are from another contributor, "imstrng," on Thingiverse. I included them in this post in case theirs is ever removed as they are...

Bauteile / Parts: x Schablonmodul_StencilModule1x Nutenstein_T-SlotNut (je Schablone/per module)1x LehrenSatz_GaugeSet1x FräsAbstützung_MillingSupport2x S4x14 Schraube / Screw  - DIN7991 (je Schablone/per module)2x M4 Mutter / Nut (je Schablone/per...

The roof I use is the one named Tudor Style 2-Storey Wargaming House by kitch72 found here: https://www.thingiverse.com/thing:3057288/files I also included a roof version in the files with an adapted size to fit for buildings that use 3 Tiles x 3...

For smaller size Forstner bits, where the shaft diameter is either larger than the cutting head or nearly the same size, printed flexible inserts are used to keep the bits firmly in place.IMPORTANT! Tested to work with Ryobi “x-wing” style Forstner...

I used these [machine screws from Home Depot](https://www.homedepot.com/p/The-Hillman-Group-M3-0-5-x-16-mm-Internal-Hex-Flat-Head-Cap-Screws-20-Pack-44509/204801209) and matching M3 nuts, for mounting them to a 5mm-thick wood panel. ### Bungee Cord ...

The brass hardware is held in place with #4-24 x 3/16" pan self-tapping screws purchased from Amazon. The hardware is pliable for fine-tuning the fit and function of the controller. The internal support structure of the upper and lower sections may...

It is designed for M2.5 x 3mm inserts but could be slightly drilled out for use of M3 screws. Inserts are readily available on ebay by searching for "M2.5 Solid Brass Copper Metric Thread Knurl Insert Embedded Nut Round" A current example is:...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

Here it is, the Drawer Caddy, the ultimate in exo-drawer storage technology and you can have it in your home not tomorrow but with any 200mm x 200mm 3D print today! Yesthat's right TODAY! Wait it gets even better yet if you can believe it, just print...

There is adjustment on the EAF adapter, so once you slip the belt on, just slide the EAF down and tighten the bolts to tension it. You will need the following parts to install this on your lens: William Optics CAT-series mounting ring William Optics...

SCENE INFORMATION The area covered is a substantial 50 x 50 km space. This model relies heavily on OSM data for its structure. The scene has been specifically prepared for seamless use in 3ds Max and V-Ray Next software. Each image rendered was...

Apart from printed parts, you will need: * A piece of wood to mount the machine on which will then be put onto your luggage rack; I used 10cm x 70cm to have one bubble machine on each side (the wind wheel mount protruding a little over the edge of...

100Ω for a red LED)1x Small switch [4 x 9mm] (e.g. SS12D00G3 switch)1x Battery terminal [+] (e.g. a metal plate or coiled up and soldered wire)1x Battery terminal [-] (e.g. a small metal spring from a pen)A few wiresHeat-shrink tubing2x M3 lowering...

In order to support the wheels I used two screws [(1/4 - 20) x 3"] fastened with a nut to the bearing and acorn nut to the 3D printed piece E. Finally, I purchased one strap from my local hardware store that is placed into piece D to support where...

*"Main-Large Token Tray 1x5 - Tall.stl" - x *"Main-Large Token Tray 1x5.stl" - x1 *"Main-Large Tray.stl" - x1 - This tray and "Main-Large Token Tray 1x5.stl" can be replaced with another "Main-Large Token Tray 1x5 - Tall.stl", I wanted a place to...

I placed the fan above the slightly relocated CR Touch mount, which gives more coverage of the Y-axis (On my Ender 3 V2 the probe offset is x:-32 and Y:-30). I did not want to relocate the CR-Touch to the other side of the gantry like other designs...