amethyst from steven universe 3d models

A Raspberry Pi controlled set of printed components to build a 4-legged / 8 degree of freedom (8DOF) walking robot 'inspired' by the various Arduino MiniKame robots that can be found on the web..Eight servos, controlled by a PCA9685 controller board,...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

But as I'm not a very experienced acrobatic pilot, I didn't try out more, yet.If you decide to build the model, I would appreciate a short report on your experience in the comments or you can contact me via the prusaprinter messenger.This would help...

You can make the product on a 3D printer or cnc machine from plastic, glass, clay, bronze and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

So I can consider this bay as successfully working.Print instructionsI designed this with beginners in mind. I remember how terrible it is to have to remove each support from several pieces, and then discover that they don't fit together because my...

Don't tighten them yet.Insert this assembly from the top into the left side of the left Z-extrusion of your V0.1. Ensure that the wire goes to the bottom end of the extrusion (tips: You can cut off the standard Dupont connector to help you get the...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

I'll just explain how to properly fill and drain the tank and how to agitate.FillingRemove the cap from the lid (DO NOT REMOVE THE LID ONCE THE FILM IS INSIDE), rotate the lid so that the arrow is pointing the drainage port on the side of the...

The mount for the Arduino Uno *may* be a bit tight, to fix this you could file the gap for the ports down, or physically file down the DC power Jack (I have found this port to cause the most pain), even then you may need to use a reasonable amount of...

The flat surface of the joint is the one pointing to the desired mounting point - usually the frame or axle, while you insert the screw from the round side, always! The rodends are printed with 10 perimeters and 100% infill, basically they are solid....

TL;DRPrint in place fidget spinning finger ring in all sizes.  Giveaway As a owner of a 3D printer, you know the situation, that anyone who visits you to have a look at your printer, likes to get something printed from you. While you...

You can feel the initial resistance to the file from the ridges. Notice how, after a dozen light strokes you can feel that resistance fade ... you've knocked down the ridges. I then roll the part while it is on the cylindrical file and I file down...

The fans can be controled by the control board with a enclosure thermister (if you have enough outlets/pins on the control board). UPDATE 17/12/2021 Passive chamber temps just from the heated bed were climbing over 45°C so I have added a printable...

*Build can also be found on [PrusaPrinters](https://www.prusaprinters.org/prints/68735-prusa-slack-lack-enclosure)* --- **Purchase Parts:** * QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening) * QTY 8 - 6x50mm...

I bought mine from here. I used M3x10, but you can use something a little shorter too. I did not use nuts, but if you could, if you find the screw is not fasten enough</p> <h4>InnerTrackFrame Mounting point</h4> <p>These blocks support the motors,...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

There is room below the fan for a heatsink up to 15mm thick.&nbsp;In the pictures, I have laser cut three of the sides from 3mm thick acrylic, but these parts can be printed instead.&nbsp;You will need a USB to SATA cable to connect the drive to the...

*I used brims on: windshield front_hub_bolts front_glow_red back_glow_red axles 5 - The windshield prints well, however depending on your slicer settings/filament/printer, one edge may suffer from overextrusion. If this happens on your print, do not...

Made from durable materials that withstand daily use, this Barbasol razor holder is built to last. Its sleek design complements any bathroom decor, making it a stylish addition to your shower or countertop. With its easy-to-use design and compact...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

I've fitted my small hinges incorrectly! Fear not, there may still be a solution. If your small hinges seem to restrict your mask from opening, try printing out one of the "ShortArmV2" hinges. ...Replace one or both of your small arms with this and this...

oil) on it.attach brackets on all 4 corners to hold the base plate (height from floor to underside of the board ~ 44cm).attach with a bracket the base plate to the wall. (not mendatory, but I recommend that because it brings lots of stability)Put...

PLA was superb though.Fin sticky-outy-nessso50 - these fins only stick out 50mm from the side of the bottle. They print on a Prusa miniso65 - these provide the best performance but need a bigger print bed - the Mk3Fin heighth100 - perfect for the...

One of the screws that are used to mount the Rear Plate to the Rear Rotor Housing is in the way, so I shortened the Sparkplug Base so it would fit to the same depth as the rest of them, and glued it in. When you open the motor, be sure to remove the...

Important note: Feel free to ask any question related to this project in the comment section, but notice I do not own any email account with names related to this page or my youtube channel, and I don't feel comfortable opening any links from...

Therefore, I would recommend taking from this project only a new power system and a new, more massive second leg. As well as a back cover with a control panel. If you are not going to buy more powerful and expensive servos, then I do not recommend...

It is easiest if you start with the chain hanging down from the handle. Start spinning slowly, and then start to vary speed, and even reverse the direction. Speed changes should be gentle, because abrupt changes will cause the chain to jam and fly...

Furthermore, 3D printing enables the use of a wide range of materials, from metals and plastics to ceramics and glass. This opens up new possibilities for creating unique textures and finishes that can add an extra layer of depth and visual interest...

Also, changing the filament was a challenge with the height of the printer when it is placed on a table or plate. Destination: The filament spool should be placed at the bottom to make it easier to change and not have the weight of the spool on top....

The Original Palice Keyboard also did not involve any bill of materials or recommendations for putting it together, this remix will include some instructions if you haven't done anything like this before (like myself). Updates to the original Palice...