anet a8 cooling nozzle 3d models

One wingtip have a hole so it can suck fresh and cool air inside the wing to prevent the VTX to heat up too much. Make a tiny hole in the wing to let air enter in. Print it flat, no support. Different models to come... That's it for the...

I don't mean to toot my own horn, but I find this really cool, and I would love to see yours. thanks.</p><p>Check out my mini monitor stand.</p><p><a...

I have not tested them personally so if you need assistance, speak to the mod/remix designer. E3D V6 Bowden Mount If you want to use an e3d v6 bowden setup with STEVE, this mod will allow you to attach directly to the stepper motor mount with...

Heat up the leftover gelatine in a microvave and pour some more until the mold is full again.Leave to cool.The sink is your friendWaitThe longer the gelatine sets, the firmer it gets and the better it separates from the mold. Do not be hasty, it...

One wingtip have a hole so it can suck fresh and cool air inside the wing to prevent the VTX to heat up too much. Make a tiny hole in the wing to let air enter in. Print it flat, no support. Different models to come... That's it for the parts! ...

They can stick the first time and require some love taps from a hammer. The mold needs to be somewhat warm or else the metal gets a rough and pitted surface from cooling before completely forming. You can use a heat gun to warm it up (quick) or what...

I have printed the drawers with 0.2mm layers but higher or lower layers would also be fine.The drawers are designed to be printed as spiral vase.And to make the parts a bit more rigid you can preferably change the extrusion width to 0.65 or print...

ENGFull article: https://blog.prusaprinters.org/how-to-print-for-animals_46054/Assembly and recommendations:All boxes are easy to assemble:&nbsp;simply use a piece of filament for hinges and M3 screws or wires for attaching to a solid...

If printing by fdm home printer, you can rotate the design on the bed to give horizontal or vertical print lines...or just take as long as needed and go for ultra detail and minimal print nozzle size for a more professional looking finish. or just...

0.7 for a 0.35 nozzle at 0.2mm layer height. Minimum is extrusion width.<br/> spacingRings = 0.6;</p> <p>// Number of rings to print. Rings will be lost if their radius is less than the height and you even might get a hole.<br/> numberOfRings =...

... in the Z axis direction and adjust accordingly to make sure the pins cannot move up or down. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: 0.5mm nozzle Infill: 85% or better Notes: I printed this in ABS

The multicolour designs are achieved by simply doing material swaps on a standard single nozzle FDM printer.The box is opened by turning the twist collar to unthread it and open the mechanism. It is further rotated, while holding the base stationary,...

I've made some small changes to make them even better (full history below).Having recently purchased an Original Prusa i3 MK2, I was dissatisfied with the poor bearing mounting method that can easily introduce variability in the Y and Z axes.Inspired...

These are the general settings I used:3 walls, .2 layer height (I use a .4 nozzle)10-20% infill (10% Lightning should be fine, even for the Racks – use something strong like Gyroid or 3D Honeycomb if you're worried about heavy items)at least 3 bottom...

This allowed the bearing diameter to be 52mm.Added parameters for Lee Fung spools.Removed separate KOIL design - KVP KOIL is compatible with SlantSpool, and provides a SlantSpool STL on their website.3.1: Updated Inland/eSun inner width, thanks to...

Dimensional accuracy needs to be optimal and things like layer change zits, nozzle oozing, and/or stringing need to be minimized. That said, I didn't do any special calibration for the MK3S I used (I'm probably spoiled by this printer) and printed at...

The infill is 30%, the nozzle is 0.4mm, and the layer height is 0.2mm.The combination of Propeller_90mm.STL and gaer_rod_20mm.STL is optimal for playing indoors, while the combination of Propeller_150mm.STL and gaer_rod_25mm.STL is optimal for...

Do not use warped parts.Settings0.4mm nozzle4 perimeters0.4mm extrusion width (0.45 probably works too)30 to 40% infill5 top and 5 bottom solid layersPETG or betterPart OrientationThe STL files already have the correct orientation for...

To hopefully help avoid pitfalls, here are some problems or annoyances which may help to be mindful of: * Wood PLA is stringy and abrasive, if using it, try a 0.6mm steel or hardened nozzle as I did (had no problems with it). It can help to slow it...

Narrow computer fan screws (with blunt ends and very coarse threads made for cutting their own threads in plastic) 1cm-long and 3mm diameter would be ideal if you can find them (note that these are smaller than the most common...

I found that printing the larger arm with the holes in it was a bit of a pain since the small edges curled just enough to catch the nozzle when it traversed, and pulling the part off the bed. I made another without the holes which may be easier to...

Annoying, I know.&nbsp;The case consists of a left and a right bottom part, a left and a right structural part, an IO shield that makes up the back of the case, and some small clips and trim pieces to hold it all together.Print time for all that...

For the spit roast turning thing I used a nozzle cleaner wire that comes with an Ender 3 and stuck it through the holes in the roaster, bent it, and cut it to size using flush cutters. Once I was happy with this, I put some putty around the wire to...

:)For parts with little surface area contacting the print bed, eg planter modules, an inner brim can be used to promote bed adhesion.I recommend using PLA+ and strongly recommend you find food-grade filament to print with.[^4]Generally, I've been...

Turned out that blend flexed just enough that the extruder was forced up by the pressure at the tip of the nozzle.I do not recommend any Nylons, with or without CF, they are too flexible and prone to deformation when warmed with pressure applied. All...

Firmware The firmware has been modified in many places and files to get it fully working. All changes are marked with text /*RAMPS*/, so it can be easily traced using Find/Search option in text editors (or software like Visual Studio or VS Code)....

Included is an STL mesh containing all the parts, and a multi-part object with separate meshes for the letter blocks, the base, and the hearts on the base that could be used for printing with a multi-nozzle printer. ###Customizable Triple...

:) There are two variations of the model; one has an additional thin cutting edge that is 1 mm in height and about 0.5 mm in width, so if you have a 0.4 mm nozzle, it will be a single path wide. That's the one shown in the photo. It's probably the...

I have printed the drawers with 0.2mm layers but higher or lower layers would also be fine.The drawers are designed to be printed as spiral vase.And to make the parts a bit more rigid you can preferably change the extrusion width to 0.65 or print...

You can set the parameter handle_fingergrooves to true once you set your hand measurements.Otherwise, see the print settings for each individual part below.Print SettingsOverallResolution:0.4mm nozzle0.15mm layers for propeller, 0.20mm for everything...