aurora a3 3d models
3887 3d models found related to aurora a3.thingiverse
jg aurora a3 printer x-carriage remixed for 45mm long linear bearing on top rod. kept zip tie holes internal for ease and mounting holes for jg aurora a3. NOTE: this gives more z axis clearance so you'll need longer screws for bed or put in a spacer...
thingiverse
Laser mount to convert Aurora A3 to laser engraver. Uses laser mounting holes 40mm apart. Borrows screws for the part cooler fan and keyholes to allow easy installation/removal (just loosen screws ... no need for full removal). ...Print Settings Rafts:...
thingiverse
... 2 has parameterized hardpoints. Added is an untested beta proximity sensor mount for a LJ12A3-4-Z/BX (Note that the fan bows out on the lower left so would need to extend the width there.) Print Settings Printer: Aurora A3 Rafts: No Supports: No
thingiverse
Print Settings Printer Brand: RepRap Printer: JG Aurora A3 Prusa I3 Rafts: No Supports: No Resolution: .2mm Infill: 100% Notes: These require no rafts and no supports (honestly!) when printed as oriented. Cura 15.04.4 did a wonderful job with only a...
thingiverse
Recat also has a resigned variant of the same carriage: http://www.thingiverse.com/thing:1148159 Print Settings Printer Brand: RepRap Printer: JG Aurora A3 Prusa I3 Rafts: No Supports: No Resolution: .2mm or .1mm Infill: 15% or more Notes: Highly...
thingiverse
aurora a3 x axis stop This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8QzL5fkpQgz
thingiverse
I printed this for my MK8 extruder that came on the Aurora A3 for flexible filaments like TPU
thingiverse
Part is used as the top termination for the Aurora A3 printer. ...Dimensions are made to link up to Claghorn's open cable chain links: http://www.thingiverse.com/thing:611593
thingiverse
... the extruder. The groove is designed to allow guide the filament inside a large gap without removing the filament from the extruder. After printing, just turn the part upside down, and clip on an Aurora A3 printer right above the LCD display.
thingiverse
The extruder of Aurora A3 is inconvenient for replacing the filament. I improved it. There is a sharp corner inside the extruder, and the filament is scraped. To prevent this, we installed a Teflon tube (4 mm * 2 mm) at the upper part. The...
thingiverse
Print Settings Printer: JG Aurora A3 Rafts: No Supports: No Resolution: .2mm Infill: 20% Notes: I printed this in PETG because I sometimes enclose the printer to print ABS and some of the parts have cracked or deformed due to the temps it gets in...
thingiverse
Extended version of JG Aurora A3 Glass Bed Spacer https://www.thingiverse.com/thing:2813634
thingiverse
This is cable support for JG AURORA A3 extruder . This support improves the stress of the wires to the connector. ... Thereby preventing accidents such as disconnection and poor contact.
thingiverse
... meaning. I modeled it for a box left on my desktop by chance. My bluetooth earphone came in it :) Do not push this thing down to attach to the printer. Slide it from frontside of the printer not to snap it. Print Settings Printer: Aurora A3
thingiverse
This is a Holder, for the TUSH Spool Holer for the JG Aurora A3 The TUSH Holder can be downloaded here: https://www.thingiverse.com/thing:2047554 Added new version with display window. ... Added third version with 4mm tread filament guide.
thingiverse
Remix of JG Aurora A3 Stable Feet by CdRsKuLL. This one is the stepper shim only. There are no back feet. Shim is shortened by 4mm so the machine is not raised off its base. ... This supports the stepper to greatly decrease Y-axis wobble.
thingiverse
This is support for the motors and base of the JG Aurora A3 printer because of the way the printer flexes in height around the X axis. ... Also, with my cables for the hot bed would catch on the rear motor and rod support, I added a housing to smooth...
thingiverse
... Z axis screw balance. With this gauge you can easily and quickly adjust the balance of the Z axis. Designed for JG AURORA A3. The height of the gauge was 48 mm. The gauge is approximately 0.5mm higher than the zero position of the z axis. ...
thingiverse
I used the JG Aurora A3 Spool Holder for several spools without problems. Unfortunately the latest ones are a bit wider and do not fit. Therefore I made an extension to the spool holder. If you read this before you print the original spool holder,...
thingiverse
Y axis belt tensioner for the JG aurora A3. I had a bad time when I first made this printer because it was hard to get tension, and my circles turned into ovals. After installing this, it instantly fixed the problem. Lots of room to adjust as well. I...
thingiverse
A bed mount for the JG aurora A3 to make sure your belt will not come loose. Your belt will not come loose. You're literally screwing in the belt into the plate mount, with the belt track mount attached. It's tricky, but it works, as seen in the...
thingiverse
The worst part about this if you're using a JG aurora A3 is that if you want to use the parts that are already included with the printer, such as the bearings, you have to literally take off the entire x-axis just to take out a single screw, and then...
thingiverse
Print Settings Printer Brand: RepRap Printer: JG Aurora A3 Prusa I3 Rafts: No Supports: No Resolution: .2mm or .1mm Infill: 15% or 100% Notes: For maximum strength and density, I printed this at .1mm and 100% infill, but that's probably not...
thingiverse
This is an inductive sensor mount for the JG Aurora A3 printer. Replaces the nylon standoffs under extruder heatsink. Used ABS due to proximity to the heater elements. UPDATE: Had my original mount break on me due to some vertical forces from the...
thingiverse
Remixed from https://www.thingiverse.com/thing:1683070 Parts list: M3x20 cap screw (1x) M3 nut (1x) M4x25 cap screw (2x) M4 Nyloc nut (2x) Timing Belt Idler Pulley: BIQU GT2 3mm:ID 13mm:OD Aluminum Toothless (1x) GT2 timing belt (1.2m) Caution :...
thingiverse
... Still technically a work in progress as I have yet to get a chance to print it and test it. Print Settings Printer: Aurora A3 Rafts: Yes Supports: Yes Resolution: .2 or .1 Infill: solid or 50% most likely How I Designed This Designed in TinkerCAD
thingiverse
Print Settings Printer: JG Aurora A3 Prusa I3 Rafts: No Supports: Yes Resolution: .1mm Infill: 100% Notes: Must use supports (I hate supports), but 'Touching Build-plate' only. The sides are only .5mm thick for minimum weight and the top/bottoms are...
thingiverse
Print Settings Printer Brand: RepRap Printer: JG Aurora A3 Prusa I3 Rafts: No Supports: Yes Resolution: .2mm Infill: 100% Notes: This Thingi is only 1mm thick in most places, so printing at 100% Infill doesn't increase the time much, and you'll want...
thingiverse
Print Settings Printer Brand: RepRap Printer: AG Aurora A3 Prusa I3 Rafts: No Supports: No Resolution: .2mm Infill: 15% Notes: You do not need any support for this print. Required ones are already set inside the torus for the top. Most of the sides...
thingiverse
Print Settings Printer Brand: RepRap Printer: JG Aurora A3 Prusa I3 Rafts: Yes Supports: No Resolution: .2mm Infill: 15% Notes: Rafts or Brims are required for the Clips and the Posts as they have very small bases. You should print the Clips as...