axe double sided 3d models

Experimental!Update 03.05.24Added drum screen variant 2:Variant 2 has much wider bars inside the drum than variant 1.The idea with the wider bars is that fewer longer-chip particles fall through the sieve than with variant 1 - since the material does...

The T-nuts generally over-rotate, so the "nut" side pulled into the slot doesn't get seated in the slot (unless you managed to seat them properly using exactly the right amount of gap when you inserted the nuts). To ensure good seating, turn the...

For long arms, choose the STL with 1 or 2 structural bridges.SupportsThe M5 Knobs don't require any support material.The Straight Arm doesn't require supports if you have great cooling but it prints nicer with supports touching the build plate...

(Make sure you use a support overhang threshold of less than 45 degrees, to ensure that supports are _not_ generated along the sides of the diagonal.) * _Dudd_: Print six copies of `coffin.dudd.piece-1.stl`. * _Missing Notches_: Print two copies of...

While less decorative, this makes trimming off the inevitable squished-out dough much easier than scalloped or fluted sides. ### Technical Takeaways We've learned a thing or two about making speculoos molds along the way. Here are some key...

Mid term it will be replaced by a solar tracker following the sun azimuth.For your convenience, I have created a WeatherStationOne collection including all but parts 6 and 8.End of overview common to all parts.Part 9 - Solar Panel MountThis is a...

Important warnings for the Cloudray head: * It's longer than the stock head, so be cautious not to ram it into the right and front sides when working with designs larger than A4 size, as this could damage the head and mount. * The air assist...

UPDATE #2: I've uploaded new MK2 versions of the base plates that include a small locking ring on the back side of the docking rings to keep the minis from sliding, and cut out the space underneath the minis to make it easier to remove them. I also...

- tos-miranda-pylons-no-rollbar.stl -- Side pylons without rollbar. Combined ship STLs TheTOS-Miranda-ship-stls.zip file provides the printable ships created using the parts included in...

Copper can also bring side effects when not handled properly during extraction; thus government safety regulation provides designated work guidelines for workplace usage including daily permissible exposure (1 mg/m^3 average within an eight-hour...

For some reason my attempts to print the clips along side the chain links, resulted in the clips separating from the bed and just being a lost part of the print. Thanks to them not being a lot of grams worth, there was not much “spaghetti.” I allowed...

In the past, I've often used 2-sided tape to stick converter lenses on such cameras... but removing the lens has then often removed the metal front plate from the lens assembly!</p> <p>A Permanently-Attached Adapter</p> <p>--</p> <p>My solution here...

Unfortunately as I don't yet have an assembled machine (awaiting replacement frame pieces as sent ones were cut too short), I cannot test this part yet, but it looks like it should work all okay.\r\n\r\nWhat I did was take the existing back mounting...

I did this by adding a 5V wall transformer to the "Normally Off" side of the IoT Relay. That wall transformer powers up when the printer has been shut off and keeps the input to the IoT Relay in the off state. For safety reasons, I powered the Smoke...

You can also get dupont cable in a roll and solder both sides, or whatever small gauge hookup wire you have handy. It was definitely helpful to me to label each wire so all of the soldering to the Pi could be done at once. Speaking of wiring and...

-The connection to the winch servos is a tricky one, drill a (1/16, or 1/8inch) hole through the side of the rotating part of the drum,( remove the outer portion, you won't need it) and a small 8mm shaft (attached to worm gear). Insert the paper...

2) After loading in new application called Rhino go back in to Panels > Material Editor You may have found by navigating that it’s all set ready, now select from left menu material that is using some texture of any given one (texture applied), then...

The jug has one, bow-shaped handle, and on the opposite side, in the upper part of the belly, there is a tubular spout in the shape of a reptile's maw. The entire vessel is covered with a colorful plant ornament. On the belly of the jug, there is a...

This can be done by changing the model to have zero infill and zero top, bottom and side shells, then adding a box modifier that restores these settings and placing that modifier just on what you want to print.Now print both hemispheres, and print...

**9V_base_Cover.stl** This is part of the original design for the Desk tidy/lamp, this piece slots into the sides of the Hubble_Lamp_1 series of models to block off the electronics. **Hubble_lamp_top.stl** This is part of the second set of...

You'll need fourteen 3 mm bolts to lock the smaller parts together, and trim them all to the correct length so when tightened they don't rub on the far side of the groove in the larger part that they slot into. One 4 mm bolt is needed for the...

To that end I've redesigned two support brackets and offer them with a selection of different size bores which are engraved on the side. These make assembly easier. I think that one bracket in each pair should be a neat fit to the shaft however I've...

The printed rocker arm pins have been replaced with a piece of 2.85mm PLA filament with a small hole drilled through the side for the rocker bolt (18g brad nail). Please see the pictures for a better understanding of the hardware used. I do not...

Just thread the string/fishing line through the holes and tie a knot on the other side, sliding the knot, as you tighten, to adjust the tension until it's positioned how you like it. I haven't really experimented with what string/monofilament to...

You probably will not be able to rotate it and print it 104mm x 25 x 287mm tall – It doesn't work that way , the sides will need a ton of support and making the sharp right 90 degree turn in midair will definitely fail. The 36 volt version of this...

I used a brim to print the handle narrow side down. Printed as above and assembled, this is very robust and weighs 210g. Post-Printing My friend didn't tell me about an insert ring that fit inside the original handwheel. I did know the required shape...

So please comment and post your results. The rest of the models are designed to print with support "touching build plate" and do not need "support everywhere" Depending on your printer and cooling of course. Files "should" load pre-oriented for best...

Mount snapps in easly, unscrew the rod (be patient and try to not lose screws or disalign the brass nut), mount the part first on the rod side and then snap it on, use 2 washers (its better) and rescrew all again. see photos. IF u know how,and u...

__Materials Used:__ - Rope (6mm thick 7m long) loop made with the fastener closed with 4 M3 bolts and nuts - Two broomsticks (23mm thick 1.5m long) connected with a non-bendy tube and a nail into each one - Mounted to the fence with (5mm thick 25mm...

If you are looking for more, check out our premium projects:https://codeandmake.com/premiumOpenSCAD Customizer OptionsWe recommend you use OpenSCAD to customize this design.This design has the following Customizer options:GeneralPart - Bunny or...