batmobile model

THis also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

Water cooled esc's are easy off the shelf for model boats etc and I may build enough space for a cheap (solar fountain type) water pump in the bottom. This could then feed the esc and also a water cooled motor plate. I also have a retro styled...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Larger or smaller screws can be used if you scale the model appropriately, such as M3x8 screws at 150% part scale. Note that buying in bulk from a specialist supplier is significantly cheaper per screw. There are two versions of the container: the...

I am now only weeks away from getting my own printer :) but in my preparations, i found, that i had used an inaccurate BTT filament sensor model, in my design. It was pointed out to me that i never mentioned, which panel thickness i planned...

... For more details, see my FFCP hints webpage. Just to have an actual 3D model attached to this Thing, I included my favourite variation on the boring 20 mm calibration cube, which is usually the very first thing I print when testing a new filament.

The shade is 196mm high - be sure it fits your printer's build volume. Print it in white or even translucent PLA. The model has been adjusted in Meshmixer to be solid. You need to print this in <strong>Spiral Vase Mode</strong>! This will print the...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

I made it in the same scale as that model (1:1.2168x1017, about 8cm long) so you can use the same display stand (https://svs.gsfc.nasa.gov/vis/a010000/a011500/a011568/model_stand_80mm.pdf); and in another two scales, three and six times bigger...

After way too many iterations and many failures, I'm happy to share the final design with everyone who also loves mechanically moving objects.Before we jump in: This model was heavily inspired by the work of David C. Roy (credit to him at this point)...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.&nbsp; I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

I still have not got this model right, the results are not really satisfactory. Maybe I don't have the ball geometry figured correctly or the latitudes measured properly. Sometimes the slicing does not join the detent teeth skirt properly to the...

... The endstop mount can be mounted with a single m3 screw. The endstop is triggered by the carriage body. You can move the endstop mount in any x position this way.&nbsp;NOTE: Cable chain attachments for all axis will also follow in the future.

Sorry about that).I've used these externally available models:Arduino MicroPotentiometerSteps:Solder 3 wires to the potentiometer (15cm each. You can cut them more precisely later).</li><li>Connect the potentiometer to the potentiometer_holder (Use...

Also, if you can print at such a fine resolution, you can likely print the “Powerboard with Text” instead of the “no Text” version successfully; as the name implies, the PB with Text model has all the components labeled, but the text is too small to...

Help others find the design.Max FOV DesignMeticulously modeled a 3D representation of the camera's field-of-view. Now the mount allows maximum TPU protection in front of the lens while perfectly avoiding being visible. Even with ND filters.. and even...

Then slide the little clip (that's included with the Vertical Stand model) down the back of the Wall Mount (long side pointing down and farthest away from the Wall Mount) until it slides over the back side of the Vertical Stand. It's purpose is to...

Note: Links to files and ongoing updates I'll eventually be uploading a 'finished' version of the files here to Thingiverse, but in the meantime please see my Github repository for parts files and models, and my build thread on the Duet forums for...

###Customizable Name Heart Cookie Cutter This model was generated with my Customizable Name Heart Cookie Cutter. If you want a heart shaped cookie cutter with a different word or name, you can easily create your own model with the customizer. ...

They're much harder to organize, reply-to and will take a few weeks.Use my discord!Thingiverse page is WIPMax FOV DesignJust like all other FPV designs in my profile, this is designed by modeling the FOV of the camera! Maximum protection, nothing in...

This model IS NOT HOLLOW, but is mild steel. you'll want a really long carbide bit. It drills pretty easily though, and will not affect structure. . Drill a similar sized hole on the back side of the frame. Screw the slipring adaptor into the center...

(it shows up under the images) Yes it was made from hacking and remixing various models with Tinkercad, but some parts were made completely from scratch in Tinkercad (like the entire X-axis). <a...

NewsMarch 20, 2022 added bigger hookMarch 21, 2022 added USB flash drive holderMarch 21, 2022 added hooks (12mm and 25mm, screwed with M3 screw)March 21, 2022 added box (screwed with M4x10 screw)March 21, 2022 added 2 wall parts (224x190 and...

Tactile switches are placed under the bar to detect when it is pressed. Bar Switch Subparts 3D printed snooze bar EVQ-Q2S03W tactile switches NeoPixel RGBW Stick Two NeoPixel RGBW LED sticks have been included in the front of the...

Failing that, just send me a message and I can make one that's the appropriate size.To-Do (Notes for Myself)This is an evolving project I'm using to re-learn CAD modeling, so I'm adding a list of things I'd like to tackle for my own reference...

(custom_bottom_outer_edge_chamfer_radius = .6) - Type or kind of phone: set model type number three (phone_model = 3) - Turn on a flag or no use to make image stencil and so it be applied all around and that we turn this choice option on always by...

I should snuggly fit with this model: https://www.printables.com/model/123074-ceiling-camera-mount-2-axis.03: Added the grow lights for indoor plants, see pictures. Also added a section describing the little differences. Earth anchor is good to go...

To make it waterproof, I printed it with 7 perimeter layers, following the advice from this article:  https://blog.prusaprinters.org/watertight-3d-printing-pt1-vases-cups-and-other-open-models_48949/Step 2: Test FitEnsure each piece will fit...