batmobile model

All the slicers I tried will still slice the model correctly. Parts I used:roller switch:https://www.banggood.com/5Pcs-AC-125V-1A-Mini-SPDT-Micro-Switch-Long-Hinge-Roller-p-998613.htmlslide...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If you want it with an internal battery, I have designed this same model with a hole for the battery, measuring 126x85x35mm, you have it here: https://www.thingiverse.com/thing:6016217 Required Components: - 1u Mini ZVS Module 5-12v (...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

2x 3D printed pulley wheels 2x (or 4x) 3D printed conduit couplers (depending on how you are doing the conduit) 2x 3D printed wing push brackets (based on your plane model) (For any non-symmetrical push brackets, you'll need to print a mirror...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

I recommend 8 IKEA LADDA AA cells as they are amongst the best available anywhere (https://www.ikea.com/us/en/p/ladda-rechargeable-battery-70303876/):https://cults3d.com/en/3d-model/tool/aa-six-cell-battery-holder The one piece parts need a big...

I use washers between the skate bearing and the mount to give a little clearance for the spool holder to turn (I could probably model in a little bump out instead of using washers).For adjustable friction, I've added a simple bail that attaches to...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

So, don't be alarmed if you notice discrepancies.) And another NOTE: If you're looking to upgrade the model cooling blower to a 5015, I have something very similar to the Z-19, but which supports the bigger blower: I called it the "Z-23", and here's...

The files under Skycat17 (this one and a model of the Chrysler Building) are still available for download on Thingiverse. But I have no access to even see how many have downloaded or responded. The Tripod. The Phone Holder. All 3...

Using a allen key also has a couple of smaller advantages, those being reducing the number of pieces in the model, while also providing the added benefit of acting as a keychain mount.The gadget is made up of a few common parts apart from the printed...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

Please check the images to see what it is included in this kit.This set contains: - Noble Alfar Knights (12)- Goldhorn Cervid Riders (4 + 4)- Seraphion – the Lustrous Flame- Eliora – the Dawnbringer- Lythalia – the Whisper of Secrets- Elthorion –the...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height.</p> <p>Here's a video of the toy with some details. ...The video has a lot of assembly photos at the end.<br/> <figure...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

&nbsp;900mm in length (shown in the picture is a bit too long, you may want to use 800mm instead)The bamboo skewers seems to come in different sizes, so use the file that closest match the skewers you have and scale the model accordingly. &nbsp;If...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

Your purge block will be rather large, so if you have a suitable item you can use as a wipe model, use it! Then, remove the 8 outer-most parts and core, leaving just the inner 9 components. You will need to reassign colours, i.e. red becomes the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

I based the design of these pieces off of the Ender 5+ model available on GrabCAD (https://grabcad.com/library/creality-ender-5-plus-1). There will eventually be a detailed pdf showing a build guide, confirmed material list, building and flashing...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

To aide in designing this part, I also ordered a complete Neo hotend assembly from Amazon so I could 3d model all of the parts. Unfortunately, the back plate is not available to buy, but I was able to download an stl file from another Thingverse...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...