blender procedural materials 3d models

Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool...

but it is probably best to use the simple solid one.Print the turntable_bottom part using transparent material if you are planning to use leds. The turntable_ledring parts is intended for mounting ledstrip with a maximum width of 8mm.I made the...

(outer side is ground, inside of barrel is plus).Double check all points for polarity, plug in camera and printer and enjoy!________________________________________________________________________________________________________________Bill of...

Please note that you should not use any sandpaper or other abrasive materials for deburring, as they may damage the parts. Mounting: To mount the extruder on your printer, you will need to attach it to the X-axis carriage. Please refer to your...

There is even a zip tie for your cables. Special notes: Print with a heat resistant material. I did it from PETG, if you have anything stronger go for that, as long as it doesn't flex.</li> <li>Only compatible with PrinterMods MDD 1.3 mount. Reason...

TOTAL Build COST (on 8/12/2020) was about $251.31 (not including battery) https://my.aliexpress.com/wishlist/shared.htm?groupId=100000024321909 Materials List, Cost, and Location (click that Aliexpress wishlist to get everything you need!) FOUR...

Unlike most commercially sold phone coolers, this one uses a Peltier element to enhance its performance further.The whole body is made of PLA, though any other material is fine, I guess. The cooling is done by a Peltier element with both passive and...

Minimum material, no seams, most of the times great quality. You can use it for ordinary storing-boxes, creditcard-cases, case for calculators, a cigarette box for your wooden cigarettes etc. *Limitations:* The spiral mode makes it cheap but also...

As for the cut itself - in principle, I could cut each of these materials in one pass at a slow speed, but the cut quality is much cleaner, if you make two or more passes at a higher speed, then the edge is cleaner. On the laser head seller's page...

Josh at Flite Test did a good vid about waterproofing RC electronics with Peter Sripol (Flite Test | Waterproofing Electronics) 11/6/2020 Performed a submersion test with sanded model - due to the way walls interface with fill there is capillary...

Since ABS and ASA shrink a bit after printing, you might have to print slightly larger to end up with the right dimensions for your instrument.The Flexy BitsFor the pieces marked as needing “flex” material, you should use as soft a material as you...

###Remix Details I used Blender to make this remix. I cut off a bit of the bottom of both halves, stretched out the bottom of the top part to reduce the extreme overhangs, resized it to fit the Mini Eggs, filled the hinge holes and cut new 2.0 mm...

I have experimented with adjusting this gap by rolling a few different sizes small drill bits in my fingers to carefully remove some material from the cone indentation on the rotor to smooth it out and make the rotor sit lower on the mouthpiece cone....

I have experimented with adjusting this gap by rolling a few different sizes small drill bits in my fingers to carefully remove some material from the cone indentation on the rotor to smooth it out and make the rotor sit lower on the mouthpiece...

I've included step files for most of the major components along with a complete bill of materials. If you need one of the other components in a different format, just let me know.</p> <p>The license on this is creative commons - Attribution - Non...

This is ESSENTIAL if you print with materials that expand with heat and contract when cooled like ABS and NylonOdors and most fumes will be contained during the print.Dust reduction on the print bed and the spools.It looks nice and keeps everything...

misuse could also mess up the slider so be careful, though the pom slider material is quite strong I guess. This can be a good decoy too but if anyone asks where can they get one from - you can say you dont know as it was a gift...but it says handy...

Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool...

I made my own choices when slicing so I encourage you to you print the way you choose. Material: I used Overture PLA+, no problemsCenter: 0.3 Layer height (Draft mode), 3 perimeters with 20% cubic infill, 10mm brimLeft & Right Filler: 0.3 Layer...

Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool...

Can be printed together with the pullcord from the same material, since both of them are gears.PullcordNo infill needed. The pullcord occupies the full diagonal length of the print bed and there is little room for brim or skirt material. Can be...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

With this knowledge established, one desiring to both remotely control and watch the progress of their Prusa I3 MK3(S) may deem a Raspberry Pi 3B+/4B crucial to achieving their goal. Features: Singular, seamless "OEM quality" case which carries...

Wheels:I think is especially important the material composition of the tires is as similar as posible to real ones, or better said, with the most "grip" possible. So, instead of trying to imitate the shape of the tires and print them in TPU to see...

Has a long print time, but well worth it as it only requires mount screws beyond the print material. ====================================================== I spent some time trying to find a desktop cup holder that would free up my desktop space and...

I first created a version adapted to my needs with the material I already had available, then I said to myself that my system could interest other people who may not have the same material then I have decided to decline my system in three versions:...

Can be printed together with the pullcord from the same material, since both of them are gears.Pullcord:No infill needed. The pullcord occupies the full diagonal length of the print bed and there is little room for brim or skirt material. Can be...

This ones for you guys! Video: William of Materials: 1 64mm M8 bolt and nut 1 64mm M5 bolt and nut 5 m3 10mm cone head screw with 2 nuts (non locking) 8 14mm M3 cone head screws 4x 14x5x5 bearings 2x 608zz bearings 2x m8 washers a metric crapton...

Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool...

For both solutions print settings are as follows: Quality: Standard (0.2) Infill: >=20% Speed: <=70 Support: None Build Plate Adhesion: None I used PLA as the printing material. MOUNTING THE HOLDERS (SOLUTIONS 1 & 2): Mount the choosen holder on the...