clamp champ 3d models

Clamp champ gun, the hooks move manually. ...Tested with a Wanhao I3 Mini

If you like getting a hug.. ...you will love clamp champ

3D scan based on the 200X staction figure of Clamp Champ. Scan meshed and cleaned. ... For personal use only!

Action Figure MOTU Clamp Champ Vintage Approximate Size: 7 " The figure is sectioned for your impression. It includes a sample of my master, with this file it is indicated that it is my own digitization. Any questions I'm at your service. For a...

Title: NASA Handrail Clamp Assembly Description: This Handrail Clamp assembly has been designed according to NASA’s given Guidelines and specifications in an Open challenge on GrabCAD. Seat Track meets the MS33601 Rev B standards. Components: 1)...

The above design is a Handrail Clamp Assembly (HCA) which is currently utilized by astronauts to provide rigid mounting locations required in a microgravity environment for normal daily operations. This design is made specifically for NASA Handrail...

This Champ clamp design is made keeping in mind easy locking and unlocking of the clamp from the track at the space .The locking mechanism is made of a simple clip that gets inside the cavity. ...of the second part.Only two part is to be made under this...

This clamp has been made with simplicity in mind. Only a total of six parts, four of witch are the same making for easy instillation and adjustments. ...With a 1/8 gap between the two major halves, maximum pressure is allowed to be applied to the pole...

Simple design using only 2 parts and existing stud as mechanical fastener. When the lock (red) is in place the stud is locked into position and will not slip out. Not to sure about the actual stud dimensions but the idea is conveyed. When stud pulls...

Inspired by the ratchet style pipe clamps here is my take on the NASA CHAMP project. The clamp has been designed to flex open to fit around the hand rail. Once in position the clamp is closed and locked in place with the "teeth" on either face of...

First by placing the assembly behind the clamp, moving it in until the handrail aligns with the matching slot in the CHAMP assembly, and then sliding the assembly on. ...Once the handrail is in the slot, the latch is closed over the handrail and the...

I then added another elastic element already mentioned in my previous model: NASA CHAMP Snap clamp They are a series of opposite blades that have a slight interference with the handrail so that flexing exert a compression on the rounded part to...

This Here blueprint was drawn with the purpose of being entered for consideration to be installed as a hardware clamp in the international space station it is composed of three parts one clamp and two fasteners. while drawing the clamp i kept in mind...

- Use without dispersing components, tightening and loosening the ring nut the clamp can slide along the handrail without detaching and especially without disconnecting the accessory devices that can be connected to the clamp. - Symmetric and...

The CHAMP clamp was developed to be as simple as possible with only one printed piece. Clamp is held tightly to the handrail after a device is mounted to the track stud and tightened. Four other L-Tracks are also provided for multiple mounts on one...

My original clamp design: NASA CHAMP Clamp (THE GREY) If I were to choose between these two designs, although this design is a little more complex and the print time is longer, I think it's overall strength and improved holding force outweighs those...

The main file to print is: CHAMP_TheGrey_3DPR_Withpin.STL This file has been optimized for printing with slic3r/Pronterface software and included everything you'll need to make the clamp, all in one print. It has been repaired and re-scaled. Each...

One piece friction clamp. ...Easy to print, XY printing plane should be the handrail axis.

... component maximum strength robust design interchangeable parts. ...Positive clamping holds to rail tight Pivot pin kept in double Shear to distribute load Hollow pockets are provide in clamps, not visible thankyou to all participants for inspiration

This is a twist-on symmetrical clamp. The two pieces are identical - but twisted on in opposite directions and then pressed together, they will lock into each other and should provide for a fairly strong mounting base. ... When printed with the flat...

Very simple, Four parts, tighten by hand.

I opened up my original model page to find a nice suprise, a flashing, blinking rendering of an oddly familiar model, the CHAMP clamp, "the grey".... it turns out my Italian friend, IVO ALBERTI had taken an interest in my design and took the time to...

......This CHAMP handrail clamp effectively works by sliding the open end over the rail and fastening it down by hand. Then the set screw in the middle is tightened by hand to apply pressure to the pole to prevent slippage and provide a stable connection.

Features: -Hinged multi-part design with over-center lever to lock clamp tightly in place -Lever registers over a detent when locked preventing accidental unlocking if moved along handrail -Entire design is printed, including the hinge pins (which...

Inspired by the snap buckles, composed of a single component to be printed twice. Being based on the elasticity of the components would need many print test. ... The STL files are zipped in the appropriate folder-

The closing action is performed using a cam lever that in the locking position not protruding from the overall footprint of the device which has a form very rounded shape avoiding offensive edges. The rotating pins are integral with the components,...

CHAMP 3 - 2-piece locking tapered slide This CHAMP clamp uses a 2-piece design optimised for 3D Printing. To attach; the main section is fitted around the handrail and the slide then guided into the groove. The groove is tapered with a de-tent and...

I tried to make sure that no parts would get lost in the operation. All 3 parts of my assembly are connected to each other. ...I wanted to keep a very easy working inspired from a flask.

Handrail clamp with a cam-lock- 1/4 turn fastener.

My 4th entry for the NASA handrail clamp challenge. ...Please watch the video to see how it works.