clausing lathe models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

While it worked OK for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to be...

From the original set I only did not try to model the chain gears since the chain consists of quite small parts and would be difficult to print accurately enough. On the other hand, I added many different gears to the original ones (12T, 24T). ...

March 23rd - Created a smaller prototype mockup for the bottom, mid, and top tray using measurements from the full-sized model. Experiencing corner lift on the middle tray, even with brims, and the lid/bottom of the middle tray is about 1mm too...

READ THE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO MAKE SURE YOU'RE COMFORTABLE WITH THE PLANS LAID OUT...

3D Printed Cigarette Dispenser (upto 30 standard 8.5cm cigarettes) Watch the video: https://youtu.be/-W0srrSoo7A Based on the wooden version I saw at Youtube, I designed a 3d print model myself using Tinkercad. Main parts are composed of two:</p>...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on. Print the 3 (4) parts. If you use...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

For the stand, I used a 20% rectangular infill, but much less should be also good enough to provide a sturdy build. The switch has a necessary hole diameter of 2.1mm and so has the 3D model. ...If you want to use a switch with another diameter, please...

The following customizer options were chosen for this particular model. The best approach for any specific sign will ultimately depend on your unique needs, such as text requirements and the required appearance and functionality. line_spacing =...

I might model a charger later on to hook up to my regulated power supply. Thoughts Well, in my search for replacement batteries I found so many brands who relabeled these machines... it would be interesting to find the original manufacturer or...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Updated parts files, and partial instructions will be published here as I go along, to be replaced (eventually) by the full instructions, final stl's and Blender source file (yes, I modeled this in Blender), but there is still a lot of work to do,...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

Some photos of the printed mod installed on the machine may differ from the STL due to the fact that my machine is a prototype, and I decided to change some details after discovering potential issues (so I updated the models, but for lack of time, I...

If you print this, you won't need to print the motor_plate-beta10.stl as it directly replaces it.     These parts are the latest as of 28 April 2022, if the VORON team changes the motor_plate drastically it will no longer work.     For those that...

Well first, customization (as in the mag cozys), cost (may be cheaper if you have a 3d printer already, though i hope you didn't buy a 3d printer just to print mags), and finally, they actually are closer to katanas than talons, meaning that they...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons? Feel free to remix it as you wish. It would be nice if you upload the remix...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

You may have to rotate the model so it sits correctly on the bed. Post-Printing ============= Checking the fit and gap. Angle so you can see the handle position. Body is all the way in. The ends of the handle (parts under the lip) rest against the...

In Cura, this can be accomplished by selecting the model, duplicating it, and then choosing `mirror` and selecting the red and green arrows. `Langstroth Frame Top 2 piece.stl` - **Print 1x, 100% infill, Duplicated per instructions** This piece is...

This move was swiftly followed by a large number of models being removed from other sites such as Thingiverse and MyMiniFactory. By taking this action, the LEGO group has clearly demonstrated that they do not want the maker community to produce...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 7 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Subscribe Now! A very good model from Velrock. Time-lapse print video : https://youtu.be/4lXVR1HwAAU <iframe width="560" height="315" src="https://www.youtube.com/embed/4lXVR1HwAAU" title="YouTube video player" frameborder="0"...