compact folding table 3d models

I had to buy M5x12 screws because parts were too thick for M5x10 and too thin for M5x16. 05 - 07 Jun 2016 Design and test print of the stepper holder, angle connector and table holder sucessful. 09 Jun 2016 First version of Laser cradle design and...

The power distribution on this portable panel makes 208V available via one set of female camlocks (green, white, black, red and blue), 120/208V available via two MS90555C32412S receptacles and 120V available via one 5-20R duplex GFCI...

This is probably safer for the psu components over time in restricted airflow mounting areas like under a lack table. The noise is more audible with this lid with a low hum and it runs for 3-5 minutes every 3-5 minutes. Its similar to computer level...

Inspired by the "impossible table", this stool is built to sustain the weight of a person with two tripods mounted upside-down for an optimal force transfer. As it is build around climbing rope which are elastic by nature, this stool is naturally...

Please see images for further details: this 3D print file contains STLs for the following: Walls and Supports Door Elbow Pylon x 5 Half Wall x 5 Half Wall Female Half Wall M + F Internal Door Pylon x 2 Internal Wall x 5 PYLON x 3 T-Junction Pylon x3...

I have created housing variations for the BCI BusyLight that I would like to share with my colleagues here.This variant is intended for placing the BusyLight on the table.The stand is permanently connected to the lamp and is not removable.Support...

Some of the pieces benefit from some minimal supports (pretty self-explanatory where), but I designed it to print with very little support.I kept the tolerances extremely close because I wanted the boom and bucket to hold overhead positions and not...

Finally, the tables have turned, and hunters have become the hunted. This is a full- arsenal of shoulder and backpack-mounted extermination tools for all your UGLY Mf hunting needs. Hands full, no problem! On the go and can't count on Mack for...

DIMENSIONS (AS ILLUSTRATED IN EXAMPLE PHOTOS) (as a wall-hanging ornament): 122 mm high x 156mm wide x 20mm thick (as laid-down on one side as a table ornament): 140mm across x 128mm tall x 20mm thick NOTE: Please note that dimensions will be...

I wanted to be able to have a system that could store the coins safely in the game box then were able to be quickly put on the table without having to load all the coins into the slots to vastly shorten the game's setup time. Additionally, I wanted...

* Active ability cards can be slotted in the rear slot and character tokens / markers can be rested up against it, if one prefers to use the tray rather than table space. * When the tray is placed on the lid, there is a gap underneath that allows...

Some prints for magnetic attachment of IKEA's FISKBO frames to an enclosure made of IKEA's LACK tables.Printing:Most parts can be printed with no to little support. Choose one of the holes with one of the plug designs and print 4 of each for...

All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use 220x220 - you need literally for a couple of parts to minimize support. Assembly video: 1)...

I like having money accessible at both ends of the table, so I created two money trays, one for each end. They hold the Nanty Narking metal coins well. If you prefer to have a single money tray, perhaps to place in the money spot on the Derbyshire...

VARIATION: When we're too lazy to carry the MDF to an event, sometimes we just set the walls and corners up right on a table top with no MDF base at all. It does work quite well and is much lighter to carry. VARIATION: You could make a field of any...

In a motorcycle this arrangement allows for a high revving engine that produces a lot of power high up in the rev range, which means you go fast. Additional hardware required: 4 m5 screws and nuts Top tip:before printing out various pieces...

That's why I'm focusing on designing inserts splitted into multiple components, so you can take most of them out and put on table, and other components not needed after start of the game - leave in a box. I also want each type of component separetely...

The four #8 screws actually support the entire stir plate, with the screw ends resting on the table. A non-skid mat will keep it from moving around, especially if the MagMountBase isn't well centered on the fan. I modeled this in Fusion 360, and you...

nozzle 0.6mm table temperature 115 degrees nozzle temperature 250 degrees printing speed 50mm / s lid / bottom thickness - 4mm wall thickness - 4mm filling density 100% cooling - 15% (2pcs 5015) support - yes Be sure to take care of good adhesion,...

If you like vegetation at home and you also want to obtain great benefits from this such as: -A healthier diet, prepare your favorite salads, so I present this to you: From Your Garden to your to your Table. -A #fresh #style in your home and...

Attaching an appropriate size rubber band around the 3 pegs below the table top fixed the problem. Before publishing this, I looked into the terms of service licensing that grabcad has & was not sure whether I could publish this or not. The next...

I also fixed the other files so that the bottom layers should be flush with each other. Printing: ~1.5hr per CartridgeRecommended orientation provided in gb_ready2Print Supports only needed for top piece (the one with the sticker)No need...

For my powerboard, 7mm was an optimum fit for my application. HOLE_DIA The diameter of the hole in your desk, table or bench top. <strong>HOLE_DEPTH</strong> How deep you want the plug to go. 10mm was adequate. (This does not include the top plate...

I personally double checked the size of my head using two soda cans on a table top, putting my head between the cans so that they touched the sides of my head, and then measuring the distance between the cans. I repeated this step for both length and...

  *Or "handful-of-D20 plus the average-dice-table" for the less adventurous! ____________________________________________ Finally, as a bonus, included in the zip is an Excel spread sheet as an aid to ship generation (with instructions). This is an...

Note that for slim boxes the lid does not bend as much and the locking and unlocking may be a bit harder for the first few times.The box is fully parametrizable, there is a table in the Freecad (Sliding Lid Box parametric.FCStd) file where you may...

2 of such containers should be printed, so they can be placed on 2 sides of the table, so all players can easily reach for items. Sections for health and sanity tokens have rounded bottom to facilitate item draw. 02. RESOURCES ORGANIZER 2: It has 3...

At the moment i have no holes (!) added for mounting anything, but i will provide the fusion-files to edit that for your own plugs and switches - i think that even with fan and plug/switch added it wont be heavy enough to not slide on the table, so i...

Stand the frame on a table or desk with ModularFrameDeskStand. This is a print-in-place hinged stand. Snap in one or two of these in the bottom edge of your frame. Not recommended for pictures larger than 8"x10".<br>2. Hang the frame on the wall with...

Angled feet not only help with printing without supports, but also make the parts look like they are floating above the table, and each other, when viewed from a typical high viewing angle.&nbsp;Print InstructionsPrinting the models on their side as...