custom sissy bar designs 3d models

English: Hello I have created several bases for different 1 metre aluminium LED profiles. The LED strips used here are WS2812B (NeoPixel) 144LEDs/m. The used controller is a socketed ESP8266-12F. The PCB format is 60x40mm. The aluminium profiles are...

I used (and designed the holder) for a Hella 2DA 343 106-221. There are various lights from Hella in this series with only minor (if at all) differences and package contentstwo sheet metal screws 3.5x9.5 mm (in the case your light comes without...

sketchup file included in zip folder total height 457mm total length 343mm +25mm with extension total width 256mm supports micro atx motherboards max gpu length 285mm supported 2.5 ssds 1-3 supported 3.5 hhd 1 supported psu full size atx power...

This is a replacement for the standard knob/thumbscrew found on GoPro mounts that has 3/4" (19mm) of shaft exposed.This design uses a trick to embed the bolt fully into the knob (the top of the knob is closed over, you can no longer see the head of...

https://youtu.be/qlFRljpmP_E The motivation was to design supper affordable GoTo mount for up to 12" scopes, capable for some short-exposure photography. However the total amount of money I've already spent on motors and other hardware parts is...

* Switch: + I ordered a big pack of switches - the slot is designed for these: https://www.amazon.com/gp/product/B01N2U8PK0/ref=ppx_yo_dt_b_asin_title_o02__o00_s00?ie=UTF8&psc=1 * Resistors: + Assuming you're using all the parts I've already listed,...

The higher the Spine, the more flexible the arrow will be (for bows with less poundage) while the lower the Spine (thus meaning less deflection) the less flexible (more stiff) the arrow will be (for bows with more poundage)Commercial arrows got a...

Well, something along these lines would probably be written on a product listing if this would actually be a product ^^ I have been designing tube-based frames around 10 years ago already, and i always felt a shame that this kind of fframe was...

well as they are primarily made/designed for my own collection I always sand down with fine emery then have models subjected to an Acetone vapor bath for 60 seconds when using FDM. This seals the shells and makes a smoother appearance but removes...

... screw would be preferable, if available. After threading, remove the screws and sand the mounting surface to remove the material that was thrown up when the thread was cut. How I Designed This modified the Sketchup file furnished with the original.

The model has no moving parts and is designed for display purposes. It can be used for cosplay if suitable precautions are taken, such as fitting an orange safety cap to the barrel (model provided). I do not endorse the use of this model as a...

UPDATE: New design is coming along great and will be published soon! It's a more efficient, better performing, and larger build volume due to the smaller carriage. EDIT: Wingnuts are a go! This thing is out of beta now. It works well and will get...

OverviewBased on the standard E3D V6 nozzle, this self-watering planter will help add a nice touch of green, while being on-theme for 3D printing enthusiasts.I designed the planter in two parts.  The bottom section is used as a water basin to...

I also think that this platter upgrade would be a huge boost to a player that is pretty affordable, widely available, and has a really good stock cartridge.The acrylic platter version is currently designed to be used with 3 M5 countersunk screws,...

the system is modular, and designed so the parts are small enough to be printed on a "home" printer. They all snap together. It's a pretty tight fit as is, but it's best to use some glue as well. CA (superglue) is my favorite. Mesh screens are...

Tinkercad link:https://www.tinkercad.com/things/gs2YZLfebmr Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool https://www.thingiverse.com/thing:4654396 - Rivet Placement Tool...

So why not design a rectangular case that will fit both boards and use inexpensive 5 x 2mm magnets? Because only 4 connections are required between the two circuit boards, the housing has remained relatively flat at 25 mm. The 4 pieces of wire...

This is my attempt to improve that by adding a tri-horn duct design and a second fan (because the duct on its own reduced overall cooling whilst adding direction cooling).For reasons I don't understand, my Mini's buddy board delivers 4.6v to a single...

The spacer is to put between the 5015 fans and the cover, if your spacing is larger/smaller just scale the spacer on the Z axis to match your setup. The hole for the mounting screw is designed to be 4mm in diameter, but if yours end up being...

This tablet works pretty good, but it easily over heats, and then shuts down, so I designed a cooling stand with an integrated fan that actually works. The Winbook is currently used in conjunction with a Monoprice 12 x 9 graphic drawing tablet to...

Some features of my boxes are: - Magnetic stackable - each box is the lid for the box below - Fits both standard and GeekUp Bit set ingredients - All of the standard or GeekUp Bit set ingredients for both base game and expansion fit in the boxes -...

THESE FILES ARE PROVIDED FOR FREE ON A NON-COMMERCIAL LICENSE - PLEASE DO NOT SELL PRINTS OR COPIES OF THESE FILES@Magnavis_ - Twitter & InstagramIf you would like to show some support for my files, you can do so...

so i designed this! ----------------------- You Will Need ========== * [the orignal burly mount for the dewalt 660][2] and all of it's related hardware * screws for mounting the laser and attaching the air assist > *i believe M3's will...

The built-in supports are designed for a .4mm nozzle and for the size that the model is presented. Use your discretion for which parts to use if you resize the model significantly. 2 - There are some pieces that may need brims or rafts, use your...

designed a piece to hold the leds inside the body “Led_windows_tube – MOD”, just glue your leds on it's walls. 6: a couple of pieces have been modified to have a look closer to the references i've found. Thanks to Sean Fields, and I...

... far for me this projct was really funny and I learned some insterresting things about wood working. Maybe you also learned or will learn something. Thank you for reading my instruction.YouTubeEtsyIf you like to, check out my other designs too!

Medallion, depicting the deity baphomet, that the Knights Templar were accused of worshipping, file STL, OBJ for 3D printers, two sizes two size however, the dimensions can be changed with each slicer composed of 1041 mil points all the files have...

I designed this case myself.  I wanted it to have a retro look without copying any actual computer case.  The parts are small enough to print on a Prusa Mini+, but you need to print without skirts or brims.  You also need to be careful...

I am currently in the process of designing a 3d printable fix that is more suitable. Turn on your printer and test a Y home to make sure the sensor is in the right position and working. BE READY TO PANICK SWITCH OFF INCASE SOMETHING WENT WRONG. If...

**Attention:** All parts were designed to be snapped together without the need for glue. Please print everything with a 0.16mm layer height and 0.4mm extrusion width, in a printer with a well-tuned extruder (Check [this page]...