davinci da vinci 1 0 e3d carriage and extruder drop in replacement

(Luc's repetier firmware is great!) I designed a drop in replacement that only needs some M3 hardware, an MK8 extruder gear, a 624 roller bearing, E3Dv6 hotend, and 5V fan (30x30x10 for the E3D itself, or 40x40x10 for print cooling with a permanent...

This is a precision-fitted drop-in hotend carriage for the Davinci 1.0 and 1.0a printers, designed for optimal performance and ease of installation. To bring this component to life, simply print it in ABS plastic using your Davinci printer, then...

This remix is a reworked version of the "Da Vinci 1.0 E3d Titan + V6 Direct Drive Coyote Carriage BETA by Debio." The original carriage was installed, but clearance issues arose with the extruder motor striking the back metal shelf. To overcome these...

I've created a second version of this fan duct that should eliminate the need to feed the belt through it and provide additional print bed clearance (the first version hits the mount screws in the four corners of my print bed). I haven't tested this...

22 November 2017 This is a complete replacement of the Bowden Extruder for the XYZprinting Da Vinci 1.0 Pro printer, with the exception of the Stepper Motor, which remains intact. Over time, the original extruder weakened, and the idler pulley...

Print Settings Printer: DaVinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to perform a significant amount of carving to get this to fit properly. ...I need to update the drawing, but with some effort it will fit...

It seems to work better than the stock but isn't up to par with what I expected. Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of...

Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of carving to get this to fit. ...I need to do an updated drawing but it will fit with a...

This is a somewhat hacked-up re-mix of the body of bdwalker1's "XYZ da Vinci 1.0 Pro E3D V6 Drop-In Cartridge Mount" to make it hopefully cool the E3D hotend better. I closed some gaps that let cooling air escape where it shouldn't, opened up the...

... ... Drop-in E3D Mount for modified Davinci Printers. This design will not work with stock printer hardware or firmware, as there is no provision for the sensor board. Inspired by the Prusa hotend mount design, I created this unit with similar lines.

The text appears to be a log of updates and notes from an individual who is designing and manufacturing a custom drop-in cartridge for an E3D V6 hot end. The writer has been making iterations and refinements to their design, noting changes they've...

After inserting a fresh drop-in cardridge, my E3D v6 wasn't aligned properly with the original PCB. Therefore, I adjusted the mounting of the heat sink by 1mm to compensate for this discrepancy. This modified design prints without supports, ensuring...

... Required extra parts: -LM8UU linear bearings (four) -M3 screws and nuts (three) -30mm fans (two) -Ziptie Optional extra components: -LED diodes (four) -NeoPixel strip (the length will depend on the number of diodes per meter in your chosen strip)

I am currently developing a new extruder for my Da Vinci 1.0, drawing inspiration from Budas' design for 1.75mm filament. My version features two front fans that blow air directly onto the heat-sink, while the third fan acts as an extractor,...

I am designing a new extruder for my Da Vinci 1.0, drawing inspiration from the Buda design optimized for 1.75mm filament, with a few key modifications to suit my specific needs. The front two fans blast air directly into the heat-sink, while the...

I encountered numerous challenges when searching for a reliable working model that printed straight from my DaVinci without requiring extensive modifications. My goal was to create a solution that addresses these issues, making it immediately usable....

Frustrated by recurring clogs in the Da Vinci Jr's hot end, I created this innovative mounting block. ...It redirects airflow to an E3D v6 (clone or original), channeling it through the back and bottom for enhanced layer cooling, much like the official...

This is for someone who wants to upgrade their Da Vinci Pro 1.0 to direct drive and to work with the E3D All-metal v6 HotEnd. I used the E3D Titan extruder with a modified heatsink cover to fit the E3D v6 Volcano. This requires cutting off the old...

Remix of https://www.thingiverse.com/thing:2826917 designed to support optical endstop usage with DaVinci 1.0a printers, although its compatibility may vary with older models like 1.0 or 2.0. ...I also identified the carriage flexing towards sides due...

My E3D V6 hot end carriage for my Davinci Pro 1.0 I have an old Davinci Pro 1.0. I bought it when they first came out way back in 2015. I pre-ordered it and got a discount. It has been a good printer over the years and of course I have done some mods...

**Step 3: Assemble the Idler** Take your printed out http://www.thingiverse.com/thing:15718 idler and two idler extenders, adding them to the extruder stepper motor as shown in Pictures 7 and 8. You will need long black screws and springs (salvage...

Human: Alternative carriage for the XYZ Printing Da Vinci 1.0 printer using an E3D Titan extruder with an E3D v6 hotend.\nDirections:\nPrint using ABS or another high-temperature-tolerant plastic at high infill (I did 90%) as it's designed to print...

... cooler boosts print quality. ...Designed specifically for the da Vinci Jr. 1.0 Pro 3D printer, it pairs perfectly with a 45mm radial fan. ...I've found great success using a Sunon GB1245PKVX-8 (45x45x20 mm) radial fan in conjunction with this cooler.

This is a filament Spool holder that I use on the back of my Davinci 1.0 that is flashed with Repetier Host. this has the back lid open and allows the spool to sit above the back and feed through. There are bearings in the ends that the rod goes...

This is a replacement filament guide tailored specifically for the XYZ Da Vinci 1.0, which slots neatly between the upper filament tube and the gears as seen in the second photo that is not too clear. My original piece broke somehow and each time I...

This is a remixed extruder cable chain designed specifically for the DaVinci 1.0 printer. It features a mounting bar that can be easily glued or screwed into place to secure it to the extruder. The included .stl file contains everything needed,...

Chain connector plate designed specifically for attachment on the extruder carriage. I enhanced Jgam5095's design to seamlessly integrate with superover chain links, creating four distinct variations - two for each side, each accommodating both male...

You can adapt a complete MK8 extruder and hot end into the Da Vinci 1 3D printer using this design, but you'll need fully machined hardened X-axis shafts if you use linear roller steel bearings instead of the original brass Davinci bearings. I've...

This custom carriage keeps the nozzle in its original position, allowing you to use the nozzle wiper attachments that come with the Davinci 1.0. Additionally, it features mounting points for a 40mm layer cooling blower-style fan. The specific fan...

Amazon- https://www.amazon.com/gp/product/B06XPRCMJS/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&amp;psc=1 All this while being more compact than the original "Drop-in" style carriage and prints with NO SUPPORTS! Assembly: QTY. 4 - M3x25 bolts</p>...