file folder organizer 3d models

For example, there is a tiny cube representing the Grayskull Castle, that, if it was scaled, it would size about 40 km long.The file's names explained: name_1_x_10_y.stl is 1 : x* 10^y. So _1_6_10_7 is 1:600000000 or one in 60...

It will need supports to hold up the middle of the dome if printed in the orientation I have placed it in the file. ###New style shroud I may recommend it be printed with **brim** to keep it firmly on the buildplate, as I had adhesion problems...

 Ender 3 spring kit:  https://www.amazon.com/gp/product/B07V6YCYP5General spring kit (note there are many like this, this is just one, you may find others that are less expensive):  https://www.amazon.com/gp/product/B000K7M36WI know...

I have it posted in two zip files. The first one is the lighthouse without a lighted rotating beacon, and the second one includes the parts to make it light and rotate. As always my models are free and tips are not necessary. But, they are fun. Kim ...

It is a base file for editing and hollowing out objects. All in order to obtain customizable mates.</p><p><strong>Technical characteristics</strong>:</p><p>Height: 7.6 cm</p><p>Diameter of the top: 8.2 cm</p><p>Base diameter: 6.0 cm</p><p>Volume...

Other combinations would have been possible to include, such as a one-piece that still had gaps for LED lights for those with multi-filament printers, but that need can be filled by the model I did provide, and all those different combinations would...

A ready-to-print attribution card is included with the downloadable files for this model in PDF format. * ‘Share Alike’ means that if you make modifications to the 3D model and sell or give away prints based on that modified model, you must...

That´s why the source file includes a filament ring like the ones included with the dryer, just without the tray area. However, even so my printer can handle the size, it would be a long print and I would require around 8 or 9 of those prints. We are...

In the .fbx and/or .dae files the light parameters/details should be setup in your 3D software. Free render studio download : https://www.cgtrader.com/free-3d-models/various/various-models/render-studio-for-cinema-4d ...

The location of the parts and number needed (if more than 1) are included in the file names. All directions are in relation to standing behind the telescope and looking forward in the direction that the primary mirror is facing. Parts can be...

The FLIPS .stl file that makes up part of my submission has been monogrammed specifically for Ian (with the letter "i" in the circles at the end of each arm). You will also find a FLIPS brand/logo near the temple on each arm. The logo and letter "i"...

Therefore I have added two new stl files for the Extruder Body, one that fits my 12mm style induction probe and one for the standard PINDA style. The Pinda version just has the probe mount shifted 4mm further to the right, the 12mm probe version is...

The same way the file is oriented, just open it on your preferred slicer and you'll see what I'm talking about. Doing that, the core will be more resistant to the forces applied on it as you assemble and handle the lamp. However be really careful if...

Base mesh for Woody 3D model Textures included in ZIP file : Albedo Texture maps out an object's base color information without any added visual effects, such as glossy or reflective properties. In simple terms, it's a texture that gives objects...

... The difference between the two files lies in the fan mounting holes, m3 or m4. Use the one that fits your screws. All fan and tab holes (except the bottom tab) are pre-countersunk. M4 fan screws may experience clearance issues with the power plate.

Parts guide: Use the originals from here: https://www.thingiverse.com/thing:1914138/files holder-T-upper.stl holder-T-lower.stl holder-lower.stl .. and any phone inserts The Remix Parts are: * Center_Imperiaseal_BlackBase_YourColorUpper.stl *...

it melted the PLA parts.The tracks were unreliable.It tumbles too easily, even with two big 3s 2200 Lipo batteries inside.I did not find a remix that could mount my fpv gear cleanly.After some initial awful tinkercad mashups, I bit the bullet and...

- Tools needed (other than the printer and filaments) Drill Drill bits up to 5mm Allen keys/ drivers Some grease for the washer arrangement around the rear axle M5 bolt Pliers Various files Soldering Iron Solder Heat gun or lighter for the...

IMPORTANT!: I do not advise the installation of another or higher wattage light source, because of too much heat development!Light:LED Beleuchtungsstreifen, USB TV Hintergrundbeleuchtung 6.56Ft/2m LED Band, Nicht Wasserdicht SMD 3528 5V warmweiß Bias...

Print 1 of each part (I have included both STL and 3MF files) ##**Driling The Hole** 1. Use a 2" Hole Saw 2. On the underside of the top table, measure 87.5mm from the edge of the right side of the table and mark it 3. On the underside of the top...

You may need to trim some material to allow clearance of the hotend heasink for your selected extruder/part cooler mount.Updated files are:Voxelab_Aquila_Pro Dragonfly_BMS Gantry_Adapter_FilPathFix.stlVoxelab_Aquila_Pro Dragonfly_BMS...

In the .fbx and/or .dae files the light parameters/details should be setup in your 3D software. Free render studio download : https://www.cgtrader.com/free-3d-models/various/various-models/render-studio-for-cinema-4d ...

This will make the hook stronger. Print instructionsHow does it work Printing: PETG Recommended - It helps make the latch hook flexible enough to open easily. 2 Perimeter Layers 5% Infill No Supports needed This mount is 24 cm long Hardware: 10x...

I'm including my PrusaSlicer 3MF file, so if you use PrusaSlicer it should be all ready to go for you. I picked up a two-pack of the cables and printed two docks/dock bottoms and a single shell so I could have a dock at work, too. It's working very...

Please use the files "halter_leiterplatte_duetwifi_rev105-3.stl" and "blende_duetwifi_rev105-3.stl" for this board. These parts are identical to the original ones with the exception of 2mm more space for the antenna (which requires the cover and its...

... 1mm larger, for the top. We can iterate until it's perfect, and I can even put your name right in the Summary and/or in the STL files themselves. ...Please don't forget to do the I Made One if you do - it's cool to see people using the Things here!

*** Proposed 4x4x2 Arena: There is also an Excel file for a proposed 4x4x2 arena using the methodology of dropping 1/4" polycarbonate into the slot in 10 series 80/20 framing. 80/20 Door Track is used for one side of the proposed arena (same method...

__“top_pulley_system_+IL_Flag.stl”-__ If you want a (different) flag on the top pulley system like in “top_pulley_system_+IL_Flag.stl”, find a CLEAR photo of it, convert to an svg file (I use https://convertio.co/jpg-svg/), go into your CAD...

...Printer must be capable of printing 1 single perimeter if you want to print the launcher, otherwise you should be fine as no file requires supports. PETG or ASA recommended for launcher if you intend to use CO2 as it stresses the piece quite a bit.

Instructions: Watch this video to see how it's done: https://youtu.be/jk6g_oqyR-A First, print each STL file for the bird and one stand. You can choose between a small and a big stand. The small stand should be attached to the surface with some...