functional 3d print

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

I increased the tolerances a bit in the last version 1.1 but I didn't printed it because the version 1.0 is already working good for me (after sanding). So I hope it will be ok for you. Anyway, you will still have to remove the supports and sand...

A single support (base + 2 side panels) and a nut can be printed for each spool and the spool would only be changed by releasing the wing nuts so the spool screw would not have to be removed. It'll need: -2 bearings 628 / 6-2Z (13x6x5)mm -100mm...

I haven't done a great deal of printing yet since installing these, but I thought I'd upload now and let people play with it. OK so details: You'll need to drill four holes (each one through the two layers of the base at this point), suggest 5.5mm,...

Materials needed: You will need to print the 6 gear bearing: https://www.thingiverse.com/thing:53451 ** Thanks emmett ** 12v motor 12v variable resistor with dial 10' long speaker wire 10' long lamp cord female power plug 3' copper pipe brass...

This battery holder has 2 vertical tabs intended to be soldered on a printed circuit. Here it will be necessary to fold them horizontally then solder the led respecting its polarity. To easily remove the battery, make a small hole in this holder,...

*** Do not print this in PLA as it will melt or sag inside the car *** *** You must provide a charger *** This design is tailored for a 2019 Highlander, but it should also fit 2017-2019 models; I am uncertain about compatibility with other years. I...

------------------------------------------------------------------------------------------------------------------------ Old Description...

The fit of the Pi 4 in it hasn't been verified yet since I haven't printed it. Boxes for the Pi 3 and Pi 4 with the Pi shifted to the right side and a small cutout directly across from the USB power connector have also been added. This allows you to...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

After print is complete the battery will not fit right away. You do want a snug fit. Most definatly do not want it to go flying out of the case while using it. Take a paint stir stick and super glue some sand paper to the stick and sand paper the...

Required printed parts: 2 each - Thing1 1 each - Thing2 1 each - Thing3 1 each - Thing4 Required purchased items (blue LED used, white would be better): 1 each - 5mm x 20M Double Side Adhesive Thermal Conductive Tape For Heatsink...

To prepare for printing in STL format, I plane-cut the bottom of the model to make it level. I exported Moses in various formats, hoping that the texture map would be copied intact. So far, only the DAE file achieved this; the PLY and OBJ files...

... for a security camera through a piece of glass. 1. As a way of passing USB and power cables through a metal cabinet. ### NOTE The OpenSCAD script generates models with errors, though the errors are fixed by slicers and don't cause printing issues.

I never printed outside the heat bed (300x300mm) although this printer could do much larger than that. Also, it took a lot of space and it was not portable at all. So a new printer design came into my mind. This printer has everything Big DIY Printer...

After printing the mount, you may need to widen the opening for the magnets with a 7mm drill - since the magnets I used are 7.1mm, they hold very well within the holes without any glue necessary. The bottom of the Sidewinder is made of steel while...

To be printed in ABS or ASA to resist bad weather -o-o-o-o- Porte d'entrée avec passage à 25% - 50% ou 75% pour tout type de ruchette Dadant 6 cadres. Le modèle présenté sur la photo est celui avec ouverture à 25%. Choisissez le fichier STL selon...

Check again whether these nut mounts are really free from the rail, with something thin, like paper or a thin flat print. I used a screwdriver under these nut-mount when tightening the M3 bolts, but still got it wrong when I wasn't careful. Adjust...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

Print with layer height 0.16 and 20% fill.&nbsp;If you like my designs give me like and share. If you like them a lot invite me to a coffee.</strong><br><br><a...

If you prefer the drag-chain to go up and along the y axis than you may want the vertical spacer at the mirror mounting. If you've had this experience, feel free to feed back to the mirror suppliers that their compatibility with K40 is marginal and...

... I have not mounted the printer, controller, and power supply on a base board, so the wires to the controller are not cut to length. It's still pretty messy, but I'll do it once I'm happy with the design and fix everything down. Happy printing.

To this end, there is a small slot in the base for the PiCam ribbon cable to exit.The V3.1 box has been on the printer for around 150 hours of printing with no evidence of overheating of the TMC drivers or the Raspberry Pi. I had to ramp up the ref...

... The design is 10cm diameter, I printed at 40% scale and lost some details, recommended do it bigger that 1:2 for fully details Star Wars: The Old Republic is a massively multiplayer online role-playing game (MMORPG) based in the Star Wars universe.

Adapters have been included to help compensate for the thinner cover when attaching common print fans and shrouds. This is my first attempt at a design, and the air path likely still requires improvement. ... https://a360.co/2DHCh1B ...

Just follow these three steps: 1st step: Print the most used* clip: clip_0_0.stl 2nd step: Select the clip_X_Y.stl with X > 0 for wider clip Select the clip_X_Y.stl with X 3nd step: Select the clip_X_Y.stl with Y > 0 for higher clip Select the...

Print the "_withbutton" versions of the bezel and frame, as well as the button cap. Insert something squishy (o-ring, piece of foam, rubber band, etc.) between the pushbutton and the button cap. A Raspberry Pi Zero W could be used instead of the...

A printed part would probably work as well) - 1 x rear plate : 2mm thick CF - 1 x top plate : 2mm thick CF ## Gopro mount The gopro mount comes in 2 parts: the universal mount to put on the frame. You'll need a M5 nut and a gopro screw (that you get...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...