glo hyper x2 case 3d models

I also made some adjustments - including a protection ring around the blades of the fan to avoid them flying off when it makes contact with the casing. Update 29 May 2016: Second breakdown, melted pulley and fan damaged but luckily not ruined...

In order to upgrade you will need to print the following pieces:Spool Holder Kit v2 upgrade:Spool Holder Standard Base Left v2 (qty 1)Spool Holder Standard Base Right v2 (qty 1)Spool Holder Bearing Keeper v1 (qty 4) NEW PARTYou will also need 4...

Use a lot of infill too, in my case 80%. * No part needs support, but if you want to add some on the rectangular gap on the BLTouch mount, it won't hurt. Everything depends on how well you can print bridges. Assembling tips: * First assemble the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

There is also a cap which can seal with a 2nd O-ring and is used to seal the entire container when not in use.The spool roller bogies use a ratcheting mechanism to adjust.There is a opening which should be wide enough to accommodate many different...

(Maybe invent your own Halloween game?)The box is simple to construct and I have even removed the 1st layer underneath the lid where the hinges and catch are to be glued so they can be accurately positioned.When printing with different brands of...

My design would benefit from winning this contest by being able to design a lasercut case for the electronics and make a kit that could be purchased directly by customers. I would make the 3D printed parts lasercut instead to make production easier....

Instead, each STL is printed as a different colour, or multiple colours in the case of the main STL. This means that you need to align all parts in your slicer before positioning them on the bed. All parts share the same coordinate origin. Any...

If that's not the case, use a bit of superglue to keep them in place. # STEP file For those who like to modify this thingy, the STEP is included. # Firmware And eventually, the most important part can be found in my Github repository: [The...

The defender keeps their fortress if they successfully defend against all 3 rock-paper-scissors attacks (winning or tying)Protection of your fortressWhen you roll a 7 or play knight from a development deck, you can decide to fortify your own fortress...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

This looks much better (IMO), it does not block the view of the RAM (RGB go brrrr), it also frees up a more direct airflow path toward the CPU cooler (admittedly while blocking more of the top fan), and it makes the HDD itself less visible in the...

In any case, establishments with the limit and assets might decide to deal with PR in-house, yet it requires major areas of strength for an of PR techniques and media relations. What approach does Pearl Lemon PR take to education PR? Pearl...

In this case our MyMiniFactory Store / Campaign would be greatly appreciated. Also a courtesy cross-post on our discord channel is appreciated!All copyrights belong to Hexhog Tabletops, No rights are assigned or transferred to the end-user. Our...

You don't need to disconnect any cables from your Einsy case! You will need: two m3 12mm screws (m3 10mm will work ok) two m3 hex nuts Also check out my side mounted MK3 LCD mod https://www.thingiverse.com/thing:3483560 Now you can mount a Logitech...

This upgrade requires two parts and four extra screws, as well as drilling through the black plastic casing with a 2.5 or 3mm drill bit. The screws closest to the front of the machine are 3mm x 15mm, while the others are about 8mm long. Both...

In some cases a little more and that's good because with a little more voltage (up to 12V) you can take more photos per seconds, a nice little thing that a learned making this. The original the **MN-30** was 12V according to my research (don't...

In any case, for a deflector, the strength of the aluminum-PLA bond is quite sufficient. Look applied screenshot as sample. This is how I arranged the parts of the Cone Blower Cyclone for printing. The source of aluminum is a beer can. The side...

The case has accommodations for standard CR-10S parts and connectors, but may be customized for any printer that can use the Duet 3 board. If you have a Raspberry Pi connected, note that I haven't printed the final version of the front panel vent...

**Modifying the Ammo Can** Source files are included, in case you want to adjust dimensions of the ammo can for your own purposes. I designed this in FreeCAD, so the .FCStd files are the source FreeCAD files for each part. Even if you do not use...

Then remove the PCB from the case so you can get to the bottom of it. With the bottom exposed start to heat the rest of the wire connections and gently pull them out of the board. Do not remove the green wire that went to the 24 pin plug. This is...

The 4'th wire is spare, in case I want to strobe the LED brightly from a separate supply.Results:First light! (after a little detour upgrading firmware - don't trust the included bootloader!)</p><p>Send: M48 Recv: M48 Z-Probe Repeatability Test [...]...

This is a fully customizable Comic Sign/Speech Bubble with optional magnets you can have 1 or 2 lines of text in any of the pre-seleceted Fonts. The sign can be in customized in many ways. Preview colors can be defined separately for plate,border...

H) In case just a part of your leg print fails (which sometimes happens with multiple pieces in a print), I've supplied the individual leg piece STLs. I) LAST BUT NOT LEAST! If the joints are WAY too tight, you are probably suffering from...

reassuring you that your extruder motor is chugging along, just as excited as you are to complete your next masterpiece, invention, life-saving device or toy. :) Print instructionsStuff you need: 8mm(dia) x 5mm magnet (for best fit on a BMG) or...

This is most useful for reinforcing structures internally.The standard type clips are ideal for most use cases. The A1 and A2 variants are adjustable in size, by scaling the the object on the Z axis in your slicer. The A1 clip is 10mm wide and the A2...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version At the photos you can see the contours of the...

I cannot guarantee that any other hotend (except maybe creality/ender 3 style hotends) will work with this mod.FeaturesSpace cutout to allow for a 4020 axial fan as the heatsink cooler.BLTouch support.LGX Lite mount.No hotend offset = no loss in...

10 nuts 3ma Obviously, BigMac printing must be done using a good PETG filament (I suggest PETG-Tech by FFF WORLD) or ABS (AmazonBasics in this case will be fine). ... This is the link to buy the new hotend from GearBest:...

In my case 460-46=414mm. But I had a 410mm piece, which also worked fine - I am using a [19mm reamer](http://ali.onl/1feV) to cut the pocket for the LMMU10 bearings to exact size. If you don't intend to use a reamer, you may need to sand it a bit to...