goped handlebars 3d models

I've designed custom plugs for my CBR that eliminate the passenger handlebar (spoiler) from the back of my bike. Instead of using stickers to cover the holes, I wanted something that looked nicer and could be easily removed later. These plugs still...

This mount is designed to sit right next to your handlebars, giving you an unobstructed view of the road and any instruments you need to keep an eye on. I put it to the test on a trip through Europe with two BMW F800GS bikes, and the mounts performed...

Easily install your Supernova Airstream bicycle light on a CatEye H24 handlebar mount by using the plate typically screwed onto a Cateye Lamp with H24 mount (refer to picture #5). You can find both items for approximately EUR 6,00; search for "Cateye...

Print Settings Printer Brand: LulzBot Printer: Mini Rafts: No Supports: No Notes: should print pretty easy Post-Printing Secure the quarter-turn mount to the mount arm with 8-10mm m4 nuts and screws, then secure the mount to the handlebars using 15mm...

Due to the customizer's limitations with the DXF profile, three different sets are provided (up to 31.8mm diameter) that should match your handlebar size. If needed, adjust with Openscad (source included), and print the "arm" and "nut" STL files...

The design is tailored for bicycle handlebars with a 32mm diameter. We deliberately avoided using screws to attach it to the bike; instead, two cable ties will do the trick. If you notice any tilting, just slap some double-sided tape underneath to...

This is a configuration for 7/8" handlebar (22.2mm) measured 22.32mm.Mount measurements - 24mm, so it needs a piece of inner tube to hold the part in place. Hardware:2x M3 14mm bolt (12mm bolt pictured)2x M3 nut. Print Settings Print...

... supports. Instructions Print mount & clip. Remove supports from clip and phone holder. Glue clip under the phone mount. For handlebar, print mount from here http://www.thingiverse.com/thing:163503

This is a handlebar mount for 7/8in wide bars on Honda Groms to mount the Aracer SportD and DG1 gauges. Instead of bolts/nuts, I found some nails at Walmart with a 2.85mm thickness for the hinges. Cut the nails at 90% width and another right at the...

NOTA: se la fai stampare sotto pagamento o vendi il pezzo devi obbligatoriamente donare 1€ + 10% del valore di vendita, è un prodotto fornito con licenza non commerciale.(esempio: vendo il prodotto a 10€ devo donare 1 + (0.10*10) = 1 + 1 = 2€) EN:...

To enhance grip, wrap some electrical tape around your handlebar (or use an inner tube). I've also found it necessary to secure the Lezyne mount with electrical tape, as the design tends to be a bit loose - a redesign might be in order. ... Feel free to...

Use these stands to put your VanMoof upside down without damaging the handlebars. I've included multiple versions: Simple: Print the whole thing in TPU.Overengineered but better looking: print the base in any material you want. The inside...

There are two sizes available: one for 22mm handlebars and another for 31.8mm, as well as a quickfit version featuring a spring lock. To assemble this holder, you will need one metal rod with a diameter of 2mm and a length of 26mm, two M5x20 bolts,...

My bike currently does not have the best handlebar space at a flat angle so I designed a modular orienteer plate to handle a variety of attachment angles. The clamp is designed for handle bar diameter 22.2mm and uses four M4 x 25 screws with...

The original design was for a 31.8mm handlebar with M4x16 screw, but you can easily customize it by editing the "BikeClamp" & "ScrewSet" spreadsheet in FreeCAD. For example, you can use 26mm + M5 screw instead. A_318_Clamp_with_Hinge_V2.STL:...

I use it indoors on my trainer; if you were to use this outside on something that sees vibrations I'd suggest a rubber (maybe TPU) collar between the mount and the handlebar to prevent the mount from rotating down. I'd also suggest a safety strap. A...

There are two sizes for 22mm and 31.8mm handlebar and quickfit version with spring lock. You will need one metalic rod (d=2mm, L = 26mm), two M5x20 bolts and nuts and two springs: d = 8mm for the holder and d=4mm for the lock. I do have only Fenix...

If it's a bit too tight you can open the holes with 3mm drill,-once the LEDs and connecting wire are in place secure them with silicone and let it dry,-once dry, solder a connector of your choice, and assemble the part in the handlebar replacing the...

Yep, this design is aimed towards flat bars with a 22.2mm (7/8") diameter, so won't work on road handlebars. Here's my version for road handlebars with a 31.8mm clamp diameter. As another option, I'd suggest using Bryce's awesome Transmitr remote...

**Update** Recently I changed out the front brake master cylinder on a bike and the replacement had a narrower handlebar clamp ring. So I made a 1/2" wide clamp-on spacer set to fill the gap rather than re-adjust everything else. They are for 7/8"...

You will need to download the clip (follow the link), to clip the GPS, ContentBeeline - Holder - 53 deg - v1.0.stl : Holder with 53 degres legsHandlebar-Holder Link - Inside - v1.0.stl : Part to be inside the bar between half...

This mount lets you use phone and GPS cradles with handlebar mounts on scooters that don't have handlebars. It attaches to a right mirror post. Because of vibration and stress, it needs extra reinforcement with a T-shaped piece of metal underneath,...

Yep, this design is aimed towards flat bars with a 22.2mm (7/8") diameter, so won't work on road handlebars. Here's my version for road handlebars with a 31.8mm clamp diameter. As another option, I'd suggest using Bryce's awesome Transmitr remote...

I created this to be an easy-peasy solution to mounting things on your handlebars! I wanted a print-in-place, easy-to-use, solution that could rival all the other bar attachment mechanisms that exist today. My main focus was on ease of use, as you...

This latest setup still attaches to the current handlebar clamp, but the phone holder connects to the mounting arm with a countersunk socket-head screw that holds it in place, while tension is maintained on the back by a spring, washer, and lock nut....

See the Bontrager lights page for more information. But what about my road bike? Yep, this design is aimed towards flat bars with a 22.2mm (7/8") diameter, so won't work on road handlebars. Here's my version for road handlebars with a 31.8mm clamp...

I created this to be an easy-peasy solution to mounting things on your handlebars! I wanted a print-in-place, easy-to-use, solution that could rival all the other bar attachment mechanisms that exist today. My main focus was on ease of use, as you...

Made this because I wanted a more stylish mount that I could just leave on my bike, and it fits any bike with 26mm handlebars perfectly. A lot of hard work went into creating this, resulting in several scrap prints before getting it right. The top...

This design is intended for mounting a 20mm aluminium pipe to flat surfaces in order to use handlebar mounted accessories on flat surfaces. In practice, I designed this to be used on a boat, to attach a phone charger to my boat dashboard. There...

Designed this to make it easier for my SO to carry her bag while cycling.It is meant to be used together with the ortilieb handlebar mount that is super strong and of a very high quality.This bag (Obag) has a system that allows handles and...