headphone controller stand 3d models

If you want to build the clock as shown you will need the following parts in addition to the above: 2x printed STL Back-Mounting-Frame 1x printed STL ArdNano-Case 1x printed STL Stands This will fit an Arduino Nano or Pro Mini and a small DS3231...

I have a few printers lying around that I normally use to print Nylon and Polycarbonate, and frankly, polycarbonate is probably the best option for these as they need to be stiff, strong, and stand a lot of heat, but I have a new ender 3, so I want...

Exploration Tokens: Exploration_Token_Holder - print 1, no supports, it's designed for tokens in shields (from https://www.thingiverse.com/thing:4926791 ) Intruder Tokens: Intruder_Token_Holder - print 1, no supports, it's designed for tokens in...

:DUpdate 02/03/2022: Removed old single-part Einsy stand with new two-part. I kept breaking the single piece while installing the Einsy and cables. New design makes the whole proccess much easier. SIngle part piece is kept for archival...

This is a little stand for a phone or a device of your choosing that will use 2 Ultrasonic Sensors to try and follow you. It is inspired by this project: <a...

The assembled model stands at an impressive 195mm tall. Please don't let the abundance of notes scare you away from building this model. I just like to cover all bases due to the different skill levels of makers. Print Settings Printer: FlashForge...

You can always bypass these presets and come up with your own easily with the information given here.&nbsp;Print SettingsMake sure if you use magnets to add a pause in the print, and you can also add in colour changes to make the text stand out as...

Just drag the lithophane (standing up) to the mount, and position it so that it intersects the model, while lining up the curved edges as seen in the picture. 3. While that is printing, disassemble the nightlight by pulling off the diffuser,...

Th C stands for cheap because this allows for use of the Zosi 4 in 1 Security camera internals such as the cameras and IR array. Zosi's are half the cost of the Pheonix 2 however not as good of lux value that may improve if you bust out the IR...

I needed to scale this up to hold a ball 11.75 inches in diameter, scaled as follows: 11.75 / 2.5 = 4.7 so a scale factor of 470% Print files are provided for a complete "talon", but this does not include a stand to hold it; this needs to be...

Well no.The garbage collector pick up "load", was on the https://www.thingiverse.com/thing:6468632.Have increased the lid to the size of a door, so the same container can be used for making a small work shop, selling point of the Ice Cream man and...

An enhanced PLA is sufficient for the low temp extruder, but it will not stand up to the heat when using the high temp extruder in an enclosed chamber. For the high temp I used eSuns PA-CF. The high and low temperature heat blocks are different...

&nbsp;These prints are silly strong, I could stand on one piece with all my weight. &nbsp;I also found that the default ironing flow setting of 15% was a little too much, so I changed it to 10% and it looks less smooshed, and then to 7% and it is...

Please choose pigtail option below for flying leads with no plug.Mount: This UV sanitation device has a flat base for stand alone operation on flat surfaces. We sell mounting lugs for permanent installations if needed.Note on Environment: Sunlight...

As excellent as his original work was I felt the proportions of the limbs and overall scale required some fine tuning in order to make it look better when standing on the table top! Here is a brief overview of my changes. This model is correctly...

This first model is referred to as the MK1.An enhanced PLA is sufficient for the low temp extruder, but it will not stand up to the heat when using the high temp extruder in an enclosed chamber. For the high temp I used eSuns PA-CF.The high and low...

Given the scarcity of Judge Dredd COMIC models available as finished toys, statues, etc., and the near-absence of Dredd movie 2012 toys, I offer this model as part one of a two-part diorama that can be purchased together soon and completed with a...

First you print out the "Shuttle Wallmount" standing up, of course with supports, this takes a good 4 hours. The front part should be black so that it looks a bit like the shuttle - so I printed the front piece in black with 1.5 hours of printing...

Also when you don't remove the brim it acts as a foot, so the model stands better (and I like how it looks). _______________________________________________________________________ Filament I've tried a regular white filament I usually use...

The objective here is to print a line of free standing 3D text on a breakaway bar that holds it in place as printed until installed. Ideally breakaway is the desire, but you need to use a blade to make a clean cut. I created a video to explain an...

it's a nice little stand to slide a kazoo in for storage. let's say you want to bring your kazoo somewhere so you stuff it in your pocket. it then gets dust and stuff on your mouthpiece and the kazoo becomes kind of gross. This problem won't occur if...

As told in the stand-alone manga side story Trunks: The Story - The Lone Warrior, Trunks has traveled from twenty years in the future where the world is in constant ruin due to the terror of the two androids #17 and #18. He was created by Doctor...

http://creativecommons.org/licenses/by/3.0/ Hinges, Handles, Powersupply holder/bracket source: IKEA Lack Enclosure Creality Ender 3 Compilation by Woody1978 on Thingiverse: https://www.thingiverse.com/thing:3083358 Motherboard Case source:...

You could use a nut with loctite but don't tighten it.BOM - Bill of Materials1 x Rubber Band with a suitable length (I used an elastic hair band my daugther donated)2 x M3 Hex Head Cap Allen Bolt (16 mm)1 x M2.5 allen / hex key OR 1 x M3 Hex Head Cap...

- Modular mounts for side to hold tools like screw driver stand set or plyer holders. They will use the rail system so they can easily attach to the boxes. - Spool holders. - Suggestions are more than welcome. Tips to navigate all the files. -...

the dial indicator i have is really cheap so its probably not the best thing to start with but i got the mill about 2 weeks ago an a 7x14 lathe about 2 months ago so most of my spare money has been going to buying tooling an other stuff for the lathe...

Here are the improvements:Snap-fit joints were completely redesigned in order to make a more rigid coupling still allowing an easy disassembly;Implemented a MicroSD slot for easy access to the SD card without the need to disassemble the whole case;As...

A Lapith stands in front of a Centaur, kneeling on the Centaur’s back and clasping his throat with his left hand. The Centaur, facing right, has been thrown on his right foreleg, his head is forced back and his mouth wide open. The fingers of his...

The Ark Survival Evolved logo. Hollowed for leds and wires. Stand allow space for 9v battery, I use 9v battery holder with button on/off from aliexpress. ...(<a...

The chamfered side should be against the build plate so brim removal is easier.&nbsp;Use a mid-print filament swap to make the numbers stand out, or print in white and color the numbers in with a pencil or pen. Filament swaps effect other prints on...