ipod touch first generation case 3d models

I used 60 (first layers 20) Layer Height: .28 (or finer if you like) Rafts: No! (we want a smooth surface on bottom) Supports: (only for packer) Infill: 15-20% (I like cubic) IRONING: Yes! For the base ironing is OPTIMAL - useful to get a...

The first was that there is so little space to try to fit a finger between the Index headset and the print, making this kind of pull off difficult. Taking off the magnet face cushion was necessary to make the grip usable. The second is that this...

In fact, print one of each of the ball-joint connecting pieces first and test for fit before you print everything. I had to make some minor size tweaks to get them to work on my printer. Print Settings: Printer Brand: Printrbot Printer: Simple...

First cut at the duct has been added with a temporary transition piece using a 30 mm axial fan. The duct mounts on the back, nearest linear bearings, so it doesn't interfere with layer fan and makes hot-end changes easy. I haven't tried it yet and it...

The first design works very reliably when filament runs out and the end of it comes free from the spool. BUT -- there are times when the filament is taped to or bent through an inaccessible hole in the spool so that it can't easily come free. Then...

Attention: the plate uses parameters from the bin section and vice versa, so when using the customizer, first set all the parameters, then render one object after the other and don't mess with the parameters, until the whole set is rendered,...

I did this by clamping two steel washers in a vise, back to back (first marking one washer with the desired final width), and sawing off a section with a hacksaw. I then used a hand file to file the washers to my previously marked 10mm width line. I...

First, you can print the parts needed for this project. The main bracket is the biggest part of the assembly. The post comes in different sizes based on how high you want the camera positioned and how long your bolts are. You'll need an M3 bolt...

I usually glue the first magnet in while it's still attached to it's mate, then l put glue in the second cavity and press it over the second magnet, once it's dry pull 'em apart et voila!* 2. Cut, or grind down the barb, we need it to be <14mm, make...

Measure yours first to know for sure. You may need to remix this to make it fit your hose, or design an adapter for it.</p><p>&nbsp;</p><p><strong>My PayPal tip jar: </strong><a...

chickens whirligig revisited. In the year since I first posted my Chickens whirligig, some problems have come up. This is my attempt to fix them.</p> <p>The main problem has been that it takes quite a bit of force to get the whirligig spinning. My...

The next hole should be 50mm away from the first hole, but I found it best to place the small gear in place, meshing with the carriage assembly gear, and mark the hole. Use another small bolt to attach the gear to the board; again, using a small...

Human: This is the second segment of a sequence of projects intended for first-year calculus scholars. In this series, students will gain knowledge on how to utilize different mathematical formulas to evaluate the properties of solids and containers....

The other end goes behind the first and bends up and over and down the front. The curves in the ends should both curve inwards so they can lay on the body. Use the head as a mold to form the knot and then place both parts on the body while the scarf...

12/28/2016 First flute that opens this set has fundamental note C5. I tested the printed flute sample and it perfectly matches to C5 note. The highest note (C6 without overblow) is tuned to higher air flow to play properly. Also next octave is...

The first washer should be flush with the outside of the main body with the second sticking off the side (see image). Once in place, push the small boom through to the other side to prevent accidental gluing. Once the glue has dried, the booms can be...

When rotating your wrist or forearm, there are two possible methods to consider: Firstly, the arm may be bent using 3D hinge points, then rotated to position the wrist in the desired angle. This will create a slight bulge at the wrist area due to...

The first clips securely onto your cigarette packet, while not interfering with the easy opening of the packet, and the second is a free-standing version that fits comfortably in your pocket. It gives smokers a place to put their thoroughly...

This part is directional, and mounts first to the Arm upper, then onto the Angle Adjust Mount. Both mount with M5 bolts and M5 recessed nuts. There are two arms. The truss Arm Upper needs supports due to its curvature. It's best to print the beam...

The fully flat side should go in first so that the rounded parts face the (soon to be in there) cards.Align the cross of the fan to the hole in the body. I used a little screwdriver for this.&nbsp;</li><li>Press the lever through the inner fan. It...

The first one is best suited for the older/vintage pumps with the screw on style base. The V2 version is suited for the nylon press on base (basically the current style). The nylon base is larger in diameter than the older metal base and needs a...

If you place a large marker, that space belongs to you and cannot be stolen.However, during each player's first turn, they can only place a small marker. During their second turn, they can place either a small or medium marker. For every subsequent...

First look at 3D pinball I'm making out of old door latch solenoids that have been lying around doing nothing. As a kid I wanted to make a pinball machine. So with just a few solenoids, a 3D printer, and some bits and pieces I'm going to make a two...

https://www.facebook.com/groups/1023078667749894/ Revision History R2.1.1: -Base R2.1.2: -Added Z-Axis Linear Guild Wooden Front & Back Single Compatible Part (.STL) -Nema23 50mm Spacer (Missing from Original) -Nema17 50mm Spacer (Missing from...

This is designed in order to facilitate the creation and hanging of mosaics from the 100hex project. Print instructionsCategory: Decor Summary This is designed in order to facilitate the creation and hanging of mosaics. It was specifically designed...

- https://www.aliexpress.com/item/LUPULLEY-GT2-Belt-Rubber-Synchronous-Transmission-Closed-Loop-Belt-300-303-305-308-320-335-348/32824053502.html?spm=a2g0s.9042311.0.0.Zfv6H4 From Amazon -...

I did the first version when the schematics were made public in 2019 at the Kumbh Mela in Prayagraj. Now as the temple is due for inauguration in 2023, I present to you new versions that are much easier to print. The original free 210mm version had...

Preparation To prepare, first assess the student’s current reading ability and select a word, sentence, passage, or book that is only slightly challenging. Next, have them use Spot On Reader to help with the more difficult words by moving the...

... to find settings you need. PRO TIP: when testing out new settings add the model twice with one copy inverted. Print the first 4 or so layers and cancel the print. ...This will make it easy to test the fit of each component in your adapter.

* A Lighter * Soldering Equipment Putting it All Together: Check the fan first. It Should Run at Some Speed with 9 V Supplied. It Probably Runs Too Fast. It Should Run at a Leisurely Speed. Enough to Make the Air Move, But Not Spray Your Office or...