jisoo modeling

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

Modeled to look like a pirates spyglass, this kaleidoscope will be so much fun to play with! I printed in primary colors to preserve that playfulness. The pieces should slide together right off the print bed. This was designed so that the Barrel...

In Cura, this can be accomplished by selecting the model, duplicating it, and then choosing mirror and selecting the red and green arrows. Langstroth Frame Top 2 piece.stl - Print 1x, 100% infill, Duplicated per instructions This piece is keyed so...

I added the sketchup file with the separated into groups printing parts and model of the motherboard, power supply and fan. You can notice, that motherboard is too close to the HDD cage. If you use mini-ITX board with the cooler not higer than 3,5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

There is not a real place for the buttons, but hotglue eliminates hours of 3d modelling, at least for me, and works well enough. This is a WIP so take as it is. For the wiring it's quite straightforward, take the 2 external potentiometer pins an...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

I could not prevent warping completely but using a strong construction lamp to heat up the model seemed to improve the result. I am glad for any tips on how to prevent warping. (I am new to 3D printing and so far brims did not prevent warping, and...

How I Designed This Modelled in Blender using digital calipers for measurements. Went through 10 iterations getting the LED channel profile fit correct, and 3 more revisions for practical considerations. ... All parts have been checked using Blender's...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

I discovered this innovative concept on Chep's/Elproducts YouTube channel, where he credits OneBadMarine for originating the idea.\r\nhttps://www.youtube.com/watch?v=Fb4XMbZ0iA4&feature=youtu.be\r\n\r\nInitially, I encountered difficulties slicing...

 On my ESC I have to start with the minimum setting (effectively the throttle channel on an RC model), which I believe is a great safety feature.  BTW you can also program your ESC using the knob as if it was a throttle control, if your device...

Details and models may change as I continually improve it. Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten....

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I added the resistor, pot, and a switch to the power supply control box, then modeled and printed a knob for the potentiometer to hide the apprentice marks visible around where I put the pot through. Should fit any potentiometer with a 6mm shaft and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

... can get rather hot. PLA may work; I'm not sure. Use a minimum of: 3 perimeters 20% infill 4 top and bottom layers The model for the base plate isn't oriented correctly-- print it flat with the side labeled "TOP" upwards. Category: 3D Printer Parts

In the recent past, the basic Fused Deposition Modeling (FDM) technique has been augmented through an increase in the materials that can be printed. An overview of a basalt 3D printing approach for use on Mars is presented in [2]. Maintaining a...

Although the chinese version is much cheaper, be warned that some models lack the reverse polarity protection feature from the original, even if they claim otherwise on the backside. Also, some clones have a different layout with non-centered power...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 0 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

... for all of this - I am just starting to learn with Onshape thanks to TeachingTech's new series but Tinkercad is still a lot quicker for me with these simple shape kind of designs. I am looking forward to being able to create more detailed models :)

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Other causes could explain the "evidence" for the Planet Nine hypothesis, like a past close passing star, or observational bias.Type: Planet. Orbit: Sun. Orbital period: 10000 to 20000 yr Composition: Rocky, gaseous, or something...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

At each joint- extend the cable to it's most strained position and then firmly secure it to the next joint in the chain with a zip tie. Example Setup:Though I tested all of my parts and you can assemble in any configuration you like, if you want...

- [Winwill USB to PC Fan Cable](https://www.amazon.co.uk/dp/B08SVZD8MK?psc=1&ref=ppx_yo2ov_dt_b_product_details) I printed these prototypes in Black PLA with a Prusa Mini but would recommend a larger printer model to avoid wasteful support material....