jisoo modeling

--- # Assembly ## Key Switch The key switch is a two-terminal model (aka, it only has "on" and "off" modes for simplicity) intended for generic Chinese electric scooter ignition. It is intended for a through-hole of ~10mm. I made it 11mm to account...

However, for the non-threaded parts of your models there is no need to waste time and energy printing that fine (and slow). In the example below the use of variable layer height saves about 9 hours of printing time (which equals about 1.4 kWh of...

 When you slice the model for your printer, check a few crucial layers to make sure that the bolt holes and nut slots leave enough wall thickness everywhere.A note about the coordinate system:  The enclosure is modelled on it's left side,...

If there’s a flat-ish STL model that you like, you can load both this and that stl into Cura, scale and move them around as needed, and slice: Cura automatically joins models where they overlap. There’s also an insert plate that fits inside style0,...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal model (print the correct...

If there is too little filament on the coil, it is pointless to print a large model. And it's a pity to throw away the leftovers, too. But you can print such a trinket as a gift or just for your own pleasure. P.S. When printing this model, not a...

Enable the "Generate Support" setting **PrusaSlicer** Load the model as a multi-part object into PrusaSlicer. Then perform the following actions, as in the screenshot: 1. Set the supports to Support Enforcers Only 2. Right click on the rectangle...

The information-processing equipment, for its part, will convert hypotheses into testable models and then test the models against data (which the human operator may designate roughly and identify as relevant when the computer presents them for his...

CPC Farnell • Pro Elec 12V, 3A AC/DC Power Supply Adapter PEL00853 5 x Pro Elec 12V, 3A Power Adapter PEL00852 (€45) for TinkerForge Stepper Brick. Straight DC connector (model: PEL00582) 2.1mm x 5.5mm x 12mm Right-angled DC connector...

Rugged Box testdrive Artillery Sidewinder 2I utilized the model of this box from the authorWhitywhich can be found at link to the model , for testing my new printer. This box itself is parametric, excellent documentation and the flexibility to create...

So _1_6_10_7 is 1:600000000 or one in 60 million. The accuracy of the model The model was made taken these features as literal from the book: The spaceship was a cylinder 50km long and 20km in diameter, although it can be expected aliens having...

10 - 15W)Sample links:Power Cable Lamp Socket with Switch E27   -   https://www.amazon.de/dp/B00P2DV2NY/ref=pe_3044161_189395811_TE_SCE_3p_dp_1?th=13 - 12 W E27 LED Light Bulb Corn Light   -...

You don’t want them pulled too tight. Install the Chain Link Cover Clips onto the drag chain links to close the chain. Slide the Cover pieces into place over the Chain Frame Mount and the Drag Chain Arm Connector.Edit 2021/08/07: Added Genius...

 I know of only one 3D modeling tool where that is possible - without requiring that each user become an expert in 3D modeling.  That tool is OpenSCAD.  OpenSCAD has a "Customizer" feature that allows users to provide input to an...

- You can find a somewhat more detailed list of supplies in my Instructable: https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Any combination will do (as long as the driver is 4" or smaller so it fits the enclosure -...

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

9) Wire the power and sensor wires to the Adafruit Proto-Screwshield (Wingshield) using the 'Wiring' section (above) as a reference 10) Connect 5V power to the 2.1mm jack to be sure everything works as expected 11) Attach the front to the rear of the...

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

If this is true, the topography in this model is still extremely exaggerated to make it more noticeable, about 15% of the radius, giving the model an egg shape. The star-facing direction (since it is tidal locked) of every model in this post is the...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

Please review the filenames, model file comments, and pictures before starting.Non-printable parts and necessary tools:The clock movement and clock second...

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

The Jedi who wields it is called “F” in the credits.This is a remix of my older model. The biggest changes are:</p><ul><li>Improved mechanism for opening the emitter. It opens up by pressing the blue switch on the side, just as it does on screen. To...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I am planning to use 4mm pneumatic connectors to attach a teflon tube but you are free to use some filament guide from any of the listed projects from where I remixed.What you need to buy:1x Ikea Samla 22l including cover2x 8mm thread-rod, 338mm (can...