king song ks16s 3d models

A higher trolley handle for King Song S22 EUC. When printing make the bottom part 100% filled so it would not break. ... You can use the screws from original handle and you may also need to add 3mm nuts to hold the screws.

The top of the King Song S22 chassis ends with a sharp 90 degree angle, which gets painful after a while. They provide pads to help with that, but the pads also make an already-wide chassis even wider. So here's my solution. The .scad file...

A parking stand for the King Song S22. The S22 has a built in kickstand but putting it on a stationary stand will make it take up less space in your home or storage area. This stand is designed in such a way that most of the weight from the...

Extended King King Song S22 Calf Saver Inspired by by natewaddoups July 07, 2022 design: https://www.thingiverse.com/thing:5426967 This is the same idea, just a bit tighter fit and slightly extended version to better blend in with the battery box. If...

A charge port cap for the charge ports on the King Song S22. The rubber on my stock caps started to peel off so I made this replacement cap, it also add additional splash protection to protect from water or dirt being splashed up around the charge...

Update 2022-08-03: New STL uploaded, the new STL is a bit kinder on your fingers when you fold out and use the lift handle. The stock seat that comes with the King Song S22 is functional but by no measurement a comfortable seat. As a seasoned...

2022-08-23: Updated the top part of the shape to be a bit more rounded instead of sharp and pointy. A simple but hopefully effective shock damper protector for the stock shock on the King Song S22. The protector is 15mm thick and will hopefully...

If you printed the original design and it works fine for you no need to change! Protectors for the shock link on the King Song S22 meant to protect it from scratches and dents. As a frequent off-roader it happens that I pedal clip from time to...

When I switched from my Clark Pads that was 1 big pad to Grizzla pads that are 2 smaller padsI noticed that they had a tendency to move around a bit due to smaller velcro area so I made this version to make it stay in place better. A simple yet...

A trolley handle extension for the King Song S22, comes in two versions, one that extends the trolley handle by 7cm and one that extends it by 5cm. You will need to use 4x M3x16mm Philips screws for the upper part of the extension which screws...

<strong>2023-11-28: Did further refinements on this seat, I feel this is the final version now, I'm very happy with it. The seat was still rubbing a bit against the inside of my legs and causing some pain over time, what I've done is make it a bit...

This is a bumper for the headlights on the King Song S22 which is meant to give a bit of soft protection around the headlights which are otherwise quite exposed. The bumpers have an anti-glare function built into them, the lighting on the S22 is...

A custom front replacement bumper for the King Song S22. This is a modular design, you can choose to print only the front bumper or a version that has slots that supports extra bumpers on the left and right side that protects the battery case in...

King Song has installed rubber parts on the rails that is supposed to help keeping dirt out but they add a lot of resistance by themselves (this part is not a stopper! It's purpose is only to prevent dirt) 4. King Song has put grease in the channels...

Сделал упоры не педальки, чтоб передний шип 10 мм не царапал пластик крыла. Упор цепляется щелчком снизу вверх и плотно встает на стандартную педаль, но в продольном положении двигается. Потому я поставил внутри полоску 3М скоча. Заодно на упорах...

2022-12-05: Update to the mini fender, I noticed after riding a lot in dirty conditions that small pieces of gravels and sand could get in between the fender and the battery shell and cause rubbing, I have now reduced the contact area so that there...

Wanted the ability to attach a gopro mount or other accessories without keeping it semi permanent on the bumper so i created a clip that attaches to rawneis bumper that i can take on and off when needed. Added nubs to use with rubber bands to add a...

Customized version of https://www.thingiverse.com/thing:5426967 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5426967

Having disassembled my S22 a couple of times now I noticed that the original gaskets was not in the best state, the glue started to wear off and the very soft material the original gaskets are made of started to twist and become a bit malformed,...

A mudflap extension for the S22 kickstand. Even although the S22 has a pretty good mudguard the space below the kickstand means dirt and water can still spray up on the rider or riders riding behind you, this plug and play mudflap extension is...

Customized version of https://www.thingiverse.com/thing:4653615 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4653615

Customized version of http://www.thingiverse.com/thing:74322 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options:...

Added a cylinder to the back plate, works great as a kickstand

=== Handle small part (on the top of steel telescopic guides): Needed to carefully work with a knife to expand the hole in the handle PLA with 100% fill gived a good result for me. ... Install: https://youtu.be/t5D0Xf36f0A How it works: ...

<strong>Be advised: this doesn't work for the CNC sliders, I'm working on a new solution for that. Due to dimensions this fender only works on stock or 3D printed sliders.</strong> An evolution of the dirt protectors, these mini fenders (one in...

The rubber Protector that sits behind the lift handle has a tendency to easily come loose and fall off, one of mine flew away the other day and is now gone with the wind so I made this TPU replacement version that will sit pretty firmly. ... Bend the...

Groupe de chanteurs en plâtre peint, originellement appelés par l’auteur ” Chanteurs pas basques” et que j’ai pris la liberté de renommer “Gospel Song”. Chaque statue fait environ 72 cm de hauteur et date de 2004. Ces sculptures ont été réalisées par...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.35 crankExtraH = 4 diametral_pitch = 0.6 baseFrequC0 = 16.3516 gear_gap = 1 crankAxisCutAwayH = 4 $fn = 32 gearH = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: epsilonCSG = 0.1 gear_min_gap = 0.1 pinNrY = 35 pinNrX = 15 axisSlack = 0.3 gearH = 3 DEBUG_GEARS = 0 GENERATE_PULLEY = 1 crankSlack = 0.2...

king