lee jung jae model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

In this model (and most other barn door star trackers) the threaded rod constrains the main gear, and is itself constrained by the hole in the acrylic. As the hole in the perspex has to have some leeway for the threaded rod, this could result in...

So I grabbed [YucA305](https://www.thingiverse.com/yuca305/designs)'s [Drag_Chain_YZ_Slipon.stl](https://www.thingiverse.com/thing:4648673), put it into SketchUp Online, used the STL as a mask for sizes and alignment, simplified the model a bit and...

Also im not responsible for any damage your printer takes while printing this files. That said, i fixed anything on this model, and it is very much printable as is, you just may have to add holes for your hardware manually, or take the f3d-file and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 5 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

... heliostat not being able to rotate 360 degrees (since that would tear the MLI).The rover design is merely a representation of a possible movable platform and the focus of the design lies in the heliostat itself. Rover wheel model is by Daniel Loera.

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

Afterwards, place switches randomly throughout the plate and test that the switches are able to return to their top position once pressed down.If the plate doesn't fit in the case, you may want to trim the outer tabs with flush cutters, or file it...

Note that the Shapeways model has been modified to meet their minimum wall thickness requirement, so looks a little different; it uses the same idea. You'll need to order two if you get it from Shapeways, since it's only half the puzzle. On the plus...

This update is not just about keeping your Raspberry Pi 5 cool; it's about giving you the freedom to personalize your setup like never before.Introducing the GeeekPi ICE Tower Cooler for Raspberry Pi 5: Elevate your setup with this impressive cooler,...

... tolerances must be around 2 tenths of a mm, it is not essential to use CNC systems. The pieces can be easily made by any turner or by a modeling enthusiast and their cost is quite acceptable. ... Criticisms, suggestions and changes are welcome!

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the...

remixed from the great work from https://www.thingiverse.com/thing:1681442 see it move https://youtu.be/rTlbqrB86YA -- big wheel: one side glued to the axle, other side tightened with screw (drilled a 1.8mm hole and use a 2mm screw); gear on the...

Get the entire plow here: https://cults3d.com/en/3d-model/various/scx6-plow I have designed this plow for the SCX6. The blade reaches a size of 15.5 (394mm) wide. This does limit a print to some bed that have a 400mm build value. However, I have...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit. UPDATES V3.3 (slight comfort improvements over v3.2). [print 1 for each eye] Added a version for the prescription inserts from VR Lens Lab (also...

It is opened by twisting the handles on the doors in a clockwise direction.This was originally uploaded to Thingiverse in 2017, and I have now moved it here as well.I have 14 other Iris boxes designs and I have an instructable describing them and how...

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

RR35 is the smaller model of this company but then has the type of pod I was looking for. RR35 is 35 meters high, so I decided to make mine scaled at 1/35. My project was designed on SOLIDWORKS for the design and printed on my stock CR10. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...