loba from apex 3d models

An exemplar of woven wire container designed for Customer Service Representatives (CSR) A specific type of wire-constructed basket intended to cater to the needs of Client Support Representatives (CSR) A unique variety of woven wire receptacle...

I use the Nozzle X 0.4. Links: Orbiter Extruder: https://www.thingiverse.com/thing:4725897 (I just bought the ready-to-go Orbiter version from Aliexpress) Fan duct: any regular Predator fan duct would do as long as it stays clear enough of the...

Much better to go for a decent cheaper panel of lower resolution, and a driver board that supports things like VGA, S-Video, Composite, or even SCART, from the get-go if your intention is to build a monitor for an old computer. If your chosen...

There is room below the fan for a heatsink up to 15mm thick. In the pictures, I have laser cut three of the sides from 3mm thick acrylic, but these parts can be printed instead. You will need a USB to SATA cable to connect the drive to the...

(Optional), Install rubber bumpers into the base, maybe make some from TPU. The rest of the assembly should be fairly obvious, if you need further assistance, ask in the comments and I will update this write-up if needed Notes: The sliding...

I am using the iFlight Commando 8:...

A Raspberry Pi controlled set of printed components to build a 4-legged / 8 degree of freedom (8DOF) walking robot 'inspired' by the various Arduino MiniKame robots that can be found on the web..Eight servos, controlled by a PCA9685 controller board,...

There is also a strap hole, so you can use it immediately by lowering it from your neck. The device supports capacitive touch panel operation. Pass a 0.5mm steel wire through the hole at the tip and through the edge of the hole to the strap hole. If...

Introduction:Minimal setup for surveillance of any printer using a 2020 extrusion as frame.It is rotated 45° from the extrusion it's mounted on, so it can look at your build plate/print.It uses small screws and embedded magnets for alignment and...

You can make the product on a 3D printer or cnc machine from plastic, glass, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection molds...

PLA was superb though.Fin sticky-outy-nessso50 - these fins only stick out 50mm from the side of the bottle. They print on a Prusa miniso65 - these provide the best performance but need a bigger print bed - the Mk3Fin heighth100 - perfect for the...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

If it causes copyright issues, i will remove it. Remixed from: https://www.thingiverse.com/thing:4248444 https://www.thingiverse.com/thing:4614658 https://www.thingiverse.com/thing:2506910 https://www.thingiverse.com/thing:3853037...

This is based on Marlin k-factor generator with Prusa specific G-codes and settings. Naming convention for the G-code files: LA1_5-"Filament"-"Hotend temp"C-"layer height"mm-"fastest perimeter printing speed"-"Extrusion multiplier"E_mult-"Prusa...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

In marlin you need to find what you need uncomand it and compile and flash the firmware, in klipper you simply copy and paste few lines from the documentation and save it.Input shaping. The best feature of the klipper. it compensate the vibrations of...

For the smaller parts, a good first layer is helpful.*I used brims on:windshieldfront_hub_boltsfront_glow_redback_glow_redaxles5 - The windshield prints well, however depending on your slicer settings/filament/printer, one edge may suffer from...

I created slope from the base of the tray to the lip of the tray so the cubes slide out more easily than the original design. The slots for the Blue and Green cubes are slightly wider than the other slots. These wider slots will fit 7 cubes side by...

From here, the rocket will safely float back down. For a better explanation with pictures, go <a href="https://www.apogeerockets.com/Tech/How_2-Stage_Rockets_Work?m=education">here</a>.</p><h4>Printing and Outside Parts</h4><p>Printing the design is...

All parts were rebuilt from scratch in Fusion 360. Apologies in advance if any of the items below are included in another remix I have not spotted In this remix I have: 1.Created a 2 point fix solution with only one tab to provide a robust fixing...

Here is a listing for an assortment that I got mine from.https://www.amazon.com/dp/B07VS4823F?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe other aligner is printed but is wider not using the pipe.There is one more option if people want to drive the...

6-29-2020 Another Add-On Platform Stand https://www.thingiverse.com/thing:4510900 UPDATE: 6-23-2020 Added: these parts for those with smaller printer (separated the controller from the base, to be mounted with M3 bolts)...

Why the filter?&nbsp;Filter design will not interfere with internal spool or the moving bed!Apart from significantly cleaning the air inside the printer chamber the filter will also circulate the hot air in the chamber and will help it heat up faster...

(You can skip this step if you printed the Housing_AllScrews version.) First it is recommend to apply some petroleum jelly ("vaseline") or other lubricant around the seal and pistons to reduce the risk of jamming due to glue entering the cylinders,...

I also made an exploded view drawing to help with assembly.Build can also be found on Thingiverse.Purchase Parts:QTY 12 - 20x6x2mm magnets (used to secure the doors from unwanted sliding and opening)QTY 8 - 6x50mm wood screws (used to mount the...

I attempted to do a minor fix but had no luck and so just printed as is and it works great and the holes are not noticeable once the drawer is in place.At some point in the design process when I was cutting and merging the openlock parts to the...

Insert the terminals to the bottom and glue them with glue to prevent them from moving.4º Solder the positive cable of the battery connector to the positive pole of the dc-dc converter.5º Screw the dc-dc converter to the battery connector with the...

... All at OnceSurface Mode: NormalExperimental Extra Skin Wall Count: 0Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

The mount for the Arduino Uno *may* be a bit tight, to fix this you could file the gap for the ports down, or physically file down the DC power Jack (I have found this port to cause the most pain), even then you may need to use a reasonable amount of...