macap m2m m2d m2 stepless grind upgrade by 3d models

My mounting tab was too low and the cable chain would hit the belt on the side so I created this little extender to raise up the mounting point by 30mm’s. That did the trick. Now the cable chain is centered in the opening over the side belt. I...

The 5V needed by the external relays can be taken from SONOFF. The logical control of the relays is also done via GPIO pins of the SONOFF. For this, the configuration must be adapted. (Generic 18) See pictures. The 240V power circuit works in...

In the long run, I'd suggest to glue these parts together as depending on your stepper rings it might be loose or become loose over time (I exclusively buy stepper rings from VHBW on Amazon.de) You can make your life a little easier by painting the...

PS: All of this inspired by this guy's work (aside of course from Corosi and Rosenthal offerings earlier in the pandemic https://en.wikipedia.org/wiki/Corsi%E2%80%93Rosenthal_Box), particularly when he got to here:...

Be careful removing this part from the bed, since with low infill it won't be as strong -- don't try to pry it off by yanking on the long part of the stream! The "stream" part will need supports, no matter which orientation you choose.2) Print the...

I believe its the way the clock program makes the numbers by reducing the brightness to make numbers and when you mess with the brightness for all the numbers is causes issues. Stuff a epsphome programed D1 mini and wires in base. connected to...

 The device is powered by 5vdc mini USB and uses an array of UV LEDs and a computer fan to lure, capture, and trap flying pests on a sticky glue pad in the base.  Arduino Nano controller allows mode selection between always-on and auto-on at night...

He never backs down from a fight no matter how difficult it looks.ABOUT THIS 3D MINIATUREThe model is saved in STL files, a format supported by most 3D printers. This model contains only 2 parts and executed in the form of the solid figure therefore,...

Mount the fan of the original heatsink or one that you want by passing all the cables through the rear, through the channel that has the base. Remember to insert a wire for the 4-wire nema motor usually comes in the packs if you didn't need at...

It is not the best, since very little by little it continues to twist, but very little and every so often, not like before. Also, at the end, the thread breaks. More or less to give you an idea, without this I adjusted it once a week. With this I...

Use at own risk, you may have to reprint them later.------------------------------------------------------------------------------------------------------Voron Stealthburner Beta for Creality Spider V1 hotend with Orbiter 2.0 extruder (direct drive)...

| ### Blender files The constellation-blender-files.zip file contain a parts file, containing the STL parts arranged as used in the sample ship designs, and a parts source file, containing the raw blender objects used to create the parts License...

I looked at everything i printed so far, and came to the conclusion that a buildplate of 150 by 150 would be ok for roughly 50% of my workload. But while i waited on them to arrive, i found an aliexpress offer, showing 150x230mm heatbeds, in 12V and...

https://www.laptopmag.com/articles/install-manage-fonts-windows-10 Type Fonts into the search box by the start menu Click on the Fonts (Control Panel) link to open the Fonts Manager Drag and Drop or Copy and Paste the unzipped fonts into the Fonts...

If you want a good stress-free clip that doesn't clip to the spool, try the tight version of the Filament clipby motoz. These are the features of this clip: Uses absolutely minimal material! Uses as little as 0.14 m.</li> <li>Prints extremely fast!...

Constructed and put together in SolidWorks assistant In SolidWorks, the design was both created and assembled. assistant Assembled and crafted within SolidWorks, this project came to life. lineto assistant The process involved constructing and...

it appears to have been a combination of stress caused by the interference fit of the screw with repeated use strain. the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic...

ALL ELECTRICAL JOBS MUST BE PERFORMED BY AN AUTHORIZED ELECTRICIAN. FOLLOW THE RULES AND REGULATIONS FROM YOUR COUNTRY, REGARDING ELECTRICAL JOBS! WE ARE CURRENTLY WORKING ON A LIGHTING SYSTEM, FOR THE INDOOR HYDROPONIC TOWER. THE LIGHT SYSTEM IS...

There's enough detail in there to really make it shine at these larger sizes! I did all of the scaling in PrusaSlicer itself, by just plating things and then adjusting the scale of each part to 280%. I chose this scale because anything larger would...

**Background** The design for this spaceship was actually inspired by a foil gum wrapper that I'd squished between my index fingers and thumbs of each hand, thus forming the "+" shape from the front. I'd then drawn this spaceship, but was getting a...

The models are saved in STL files, a format supported by most 3D printers.Models of Porgs is available in 3 variants for each version (FDM/FFF, SLS/SLA):1. Angry2. Impressed3. CuteFDM version features: 
Each variant made as one piece with divided...

Baomain 16mm Push Button Switch Latching Square Cap LED Lamp Red Yellow Blue Green Light DC 12V SPDT 5 Pin 4 Pack https://www.amazon.com/gp/product/B01N2T2LJI/ref=ppx\_yo\_dt\_b\_search\_asin\_title?ie=UTF8&psc=1 Really any 12v 60mmx6omm fans could...

Make sure the handle end of the tube is loosely supported by a strap on the side of the kayak or else you will end up breaking the wormbracket. The easiest way to disassemble for transport is to just remove the bigpulley from the 24" tube, and remove...

A comparison to the original version by Logitech/Ultimate Ears:OriginalThis Versioncharging indication LEDno LEDmicro USB jack (cable not included)USB-C jack*too big for the Boom 3 as this dock is designed to also charge the Megaboom 3perfect fit for...

Bottom part of the PCB would slide into lips on the sides of the housing while top is secured with a screw on one side using a small bracket.Printability improvementsMost of the parts have been adjusted for better printability by removing overhangs,...

***UPDATE 04/15/2023*** ***Update the Cover_Interface_V3_LG_FDM_v2 to a new version "Cover_Interface_V3_LG_FDM_Aluminum_v5" as I found out the hard way that the front 2 m3 holes where off by 2.24mm from the rear two holes. I also added another M3...

Your Wall-Mounted Magnetic Knife Strip is now ready to use!&nbsp;Removal:Should you find the need to remove the knife strip from the wall at some point, you can do so by drilling a small hole in the decorative plugs and using a small hex wrench or...

Gerne ein Herz vergeben, eine ordentliche Bewertung raushauen und/ oder mich in den Favoriten speichern. English translation:“ELISABETH” as a printable LED namelamp.Use PETG for a better UV-resistance.I work in child and youth welfare and also use...

The factory sealed, explosion proof fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPL-LB-50LED-RT-CM is a Class I, Division 1 &amp; 2 and Class II, Division 1 &amp; 2 explosion proof light fixture that...

The LED light fixture assembly can be removed by releasing the hand knob and sliding the light and mounting bracket off of the center support while the legs can be collapsed, aiding in deployment, storage and transport. The lamp can be easily...