model resourse

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

Long story short, these gears don't work in the real word unless you really really know what you're doing (like how to avoid the bending because you know your material strength properties and your torque forces and more I don't know) Support me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

I needed a quicker and simpler solution to perform these tasks so I could focus on slicing and printing actual models. What is more basic than some good old push-buttons?</p><p>Feel free to remix it as you wish. It would be nice if you upload the...

 V4 was still a solid design, but I made some very subtle changes based on my range outing last weekend where I was using it on a handgun.The Magnetospeed Sporter chronograph has some mounting limitations compared to the V3 model, so I wanted to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

This is a remix of my previous models: [Modular Wahoo Board Remix](https://www.thingiverse.com/thing:4207631) [Modular Wahoo Board Remix Case](https://www.thingiverse.com/thing:4302373) In this new version, I have opted for a singular base with...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

I've designed some custom shelves for my Warhammer 40K model painting supplies, including paints from various manufacturers. The system allows you to mount two shelves on either side of a wall and connect them with chains. For instance, you can...

To assemble: Note - this is a somewhat challenging model to assemble, with a lot of parts, and a lot of tight-fitting pins to hold the parts of the toy together. You may also have to clean up a lot of support off the oddly-shaped pieces as not much...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 30 stencil_pattern_element_shape = 3...

... glue works for you on PETG. I have made extremely good experiences with YUKI MODEL superglue, which gives me basically unbreakable connections between PETG parts. The mounting plate and the counter plate are very simple to print on their flat sides.

Diameter is maximized over stock to reduce clearance in pump, increasing efficiency.*I guessed on this one, I'm not a prop/impeller designer so I could be way off and I don't have test data to determine if performance is improved, but pretty sure it...

Check model/bed limits when generating GCode for the engraver to ensure it fits in your bed. Protect your bed from the laser as it could heat or destroy some parts of your printer or even your eyes. If you've worked with lasers, then you know what I...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

After render the model in OpenSCAD, generate a .stl file and bring it to your 3d printer. Print the mold with either PLA, PLA+, or your favorite filament. 1>Use the 3d-printed male mold (without flange) as a template, cut multiple blades out of...

I would not recommend any non-3D modeler to build this project, as some of the parts will be hard or impossible to get, so you would have to do some modifications. This is 100% possible since I've included the 123D Design file. But it's on your own...

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 48...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

There is a tight-thread version of all the models for those wanting a tighter fit or using a resin printer. Caps Flat Cap Flat Cap with GB Logo Cap with 3/4" Loom Stub Cap with 3/4" Loom Stub and Circuit Passthrough Cap with GX-20 Geometry Cap with...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

I made it in the same scale as that model (1:1.2168x1017, about 8cm long) so you can use the same display stand (https://svs.gsfc.nasa.gov/vis/a010000/a011500/a011568/model_stand_80mm.pdf); and in another two scales, three and six times bigger...

Also, if you can print at such a fine resolution, you can likely print the “Powerboard with Text” instead of the “no Text” version successfully; as the name implies, the PB with Text model has all the components labeled, but the text is too small to...