monitor model

I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a lot of hours, dozens of printed iterations, and plenty of PLA. The IR Probe is mounted to the connector by design...

It includes:upkie_description: URDF model of the robot.aiorate: control loop frequency regulation.pink: whole-body inverse kinematics.Try the software out and head for GitHub if you have feedback.Last but not leastEnjoy building the beast!LicenseThe...

…unless you got yourself a special edition of a bobby car like a Porsche, Mercedes or the older Audi, VW or BMW models like I got. At most of the special edition you can’t fit the original push bar. I found the design of Klein-laui on thingiverse...

*** This model *** Have fun with this fidget ring! I uploaded many sizes (inner diameter in mm from 12.3mm for kids to 24mm for big fingers, with 0.3mm spacing) and three ring widths ("normal" - as seen in the picture, "thin" and "wide"). The STL...

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

... to ensure that everything ends up flush as it should be. I've included a Sketchup model with more information, like joint lines, as compared to the .stl files. ...I will post more notes on the build here in the next day or two as I have time.

Five basic shapes are available as elements:pieces with straight ends, adapters with either two plugs or two sockets, T-shapes, L-shapes cross-shapesTo make your own drawer partition, make a sketch like the image below, calculate...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

... Use your best judgement if you have more experience at printing. This is my first upload, I am still struggling with FreeCad. Hence, the models might not be the greatest so please be kind. Use at your own risk but they work on my printer! ...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

The design was modeled on the Zotac GTX 1080 AMP Extreme with the factory fans removed. I have not tried to customize the print design for a different brand of graphics card, but even if it doesn't fit, hopefully, the design elements can be used to...

The bowl model is a solid piece, and CAN be printed in vase mode / spiralize outer contour. This, however, isn’t the strongest. What I do is print them with 0% infill, 2-3 outer walls, 4 bottom layers, and 0 top layers. Basically makes it a double...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening] The last child of Minera to rise from the ocean depths as a great landmass. Tharador is the smallest of all continents and most meager...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

    Here are some key words copied from one of these advertisements if you are having trouble:PRINTINGThis model is for someone who enjoys the process of printing,  It is easy to print but there are nuts to be inserted  in both the main body and the...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

I didn't even try to 3D model anything because of the sheer size of the base plate so I cut it out of foamcore, but it could just as well just have been the minis sorted into bags instead. The tray is sized at 240x397x56mm externally. If you do...

Because of the simple geometry of the Box and the Pieces, these modest settings produce a very nice model in a relatively short print time. Please Note: Although I have not provided the solution here, I will respond to personal Thingiverse messages...

... assemble the mouse similarly to how to disassemble the G305 and use the same screws. (Check). Make sure that everything fits nicely and that all supports are removed. Supports can be deceiving, so check the original model if you need to. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

Once satisfied with the positioning, the pen can be used more aggressively to fill in the open corners of the shapes, and then along the whole mating edge.Note that the angles at the edges of each frame will not print perfectly, and are not exact in...

Those are only used to ensure consistency and are not necessary for rendering the model. I also pulled in the 40mm Fan Grill from the Sanginololo case and copied it here to make it easier to find. Those little 40mm fan grills print really nice and...

I also made some design changes to this model. First, because of the ninjaflex's floppiness, I was worried that the semiflex would not be much better, so I included a small piece that could fit into the charging port of the phone, the goal being...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

So I grabbed [YucA305](https://www.thingiverse.com/yuca305/designs)'s [Drag_Chain_YZ_Slipon.stl](https://www.thingiverse.com/thing:4648673), put it into SketchUp Online, used the STL as a mask for sizes and alignment, simplified the model a bit and...

...You can also save money if you can find a local shop that sells a retina display replacement, But be sure it's the right model. All in all you could maybe save 50~100$ depending on the parts you already own and your own creativity in sourcing parts.

I've seen some Hedron models before, but none of them were quite right to me - they got the patterns wrong or just looked off in some way. So I set out to design my own, and this is the final result. Well, these are the final results because there...

Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created and tested by Ty Mansfield, at The Tabletop Engineers.   Talarius is a melting pot...