necron texture base by 3d models

That by the way is what I recommend, makes you be able to see what's going on inside, which is neat. As for the assembly and post processing. It's pretty straightforward but might be tedious. Firstly file the ramps on the halves, you want them...

once reassembled (by holding the shell together, maybe only two or three screws) hold together and slide the new shell over the rear half of the blaster. 3. Mark the holes with permanent marker to drill out with a 1/4" bit 4. Dismantle the...

I kept exactly the same tuning as the original by changing the aspect ratio of the port. (The port cross-section, port length, and the chamber volume all match the original.) Frequency response 40Hz - 150Hz.</p><p>Fusion 360 Archive and STEP file...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

the heat generated by the quails - like +300 souls - manages to keep this room warm and cozy, no matter the outside temperature! For a workshop or small barn, fresh air without losing heat is a must. This design is not super esthetic but very...

Start by flipping the iPad so you can see the camera. Adjust the screws so that the camera is as close to the center of the hole as you can get it. Then mount the adapter to your microscope. You will need a little fine tuning and practice in order...

I was really surprised by the "creep ride" of the Buratinu. I tried to "starve" it several times in glide to see the behavior during stall. I had to wait a long time and then it merely took the nose down slightly to pick up speed.The 1600 is a...

For kids with ADHD, autism, or those who just learn differently, a spinner can be a discrete, quiet means of staying on task by occupying their hands. Incorporated into an IEP, they can be extremely helpful. After designing a couple of minimalistic...

You can use this just as a template or glue it on to the cardboard and colour in beforehand, on the computer or by hand. I’ll let you figure out how to place all the clips. Tip: place all the L pieces on the bottom peace first. So, for the Racecar...

It should be almost the same with the stock Anet firmware, and similar with Skynet3D (Marlin)\nWhen you have tuned your heater properly, the temperature will fluctuate by just plus/minus 0.5 - 1C and will be very stable.\nNotes\nActually try it...

Recommended is 008 clearance for prusament PLA(Please try higher clearance for more funky filament types such as mystique )Thick enough to be firm, but thin enough allow the LED to show.Programming the digispark usb keySet up arduino build enviroment...

I have originally posted this THING on the Facebook user group [Laserpecker 2 User Group (Unofficlal)](https://www.facebook.com/groups/lp2users/), run by [Michael Atkinson](https://www.thingiverse.com/minhraju/designs). If you do not already belong...

 Lilly was the person who they called upon to put out actual fires caused by the Twins during their frequent temper tantrums.  With the threat of Lilly approaching, the twins were off scampering away, looking for their next victim. Sidney knew the...

*Fan_Holder_40mm_Open*: Opened chassis to benefit from airflow produced by the fan all around it. Might be quieter than close version, and airflow might be more homogeneous into space. *Fan_Holder_40mm_x4*: Adapter to use four fans of 40mm. I'm not...

Hope they will get shipped by next week. In the meanwhile I printed all necessary corner rod mounts (see pictures). **Update 14** (04.06.2018): The extrusions arrived! And I already assembled some parts :) (see pictures) **Update 13** (09.06.2018):...

... an optimal user experience and proper display of content. For best results, maintain your phone in a straight or tilted position when needed. By following these instructions, you can enjoy the perfect view and utilize your smartphone effectively.

Get rid of it by reducing the number of strings to three. This version is cheaper in terms of buying goods from Aliexpress, but you will have to Tinker with printing the gear gear. The reduction ratio is 5.2 to 1. And the sides are synchronized using...

In that case, you might wish to speed the print up by downloading the version without the threads in the back. ...<i>I recommend having the threads for confirmation as there are many SAE screw sizes that are close in diameter, and the thread check will...

&nbsp;I was inspired by Prusa's efforts at emergency splints, and printed out their finger splint to try out. &nbsp;But found it lacking a key feature: integrated straps to hold the splint in place. &nbsp;</p><p>So I designed my own (it looks like a...

Now, I'm no pro camera operator by any stretch of the imagination and even with a dodgy knee, I can get great results. I can't wait to see what you guys produce with it! ... You can check out my other designs here:...

These segments are determined by a person's birthdate and serve as a framework for understanding their temperament, strengths, and weaknesses. Each sign has its own set of traits, both positive and negative, which influence how they interact with the...

Real working Lawgiver bodykit for cal.43 PPQ T4E Gun Functions : -startup-sequence as seen in Dredd movie from 2012 -real bullet count for fmj round type -low ammo detection and visualization -if slide stays in open position for a couple of seconds...

The only hitch here, is I had some QMK Proton-c controllers sitting around waiting to do something, and i didn't realize that they are getting hard to come by...so i designed and built my prototype with the proton-c. So...I went back to the...

Lossen the adjustable nuts to help put them on the 2020 extrusion later.Proceed by putting the extruder mount over the Hemera extruder. Route the BLTouch wire through the front slot, and the heat block wires through the side. Then slide on the...

Printing: Print the holder by itself. It fits on the ender 3 with zero space to spare (in the X direction). In fact the raft lines may even draw over the edge (Cura) if its not centered but since they are not connected it doesn't hurt anything. Its...

The head is without a camera, can alternatively be replaced by an FPV mount. I use the quad without. Flight videos, Gemfan - https://youtu.be/T-h9IKwNWdA Avan Rush 2.5 - https://youtu.be/Cv_Riwk8G1c If you have any questions, just write...

UPDATE: 24th August 2016 The 1.75mm Inner Shells have had their holes widened from 1.8mm to 2mm as requested by many people so that 1.75mm filament should hopefully now fit! Sorry it took me so long to do this! UPDATE: 19th July 2016 Due to tolerance...

My rendering intends to emulate a rendering created by TrekBBS user Prologic9’s TOS Miranda that was created all the way back in 2012. Since then, there’s been many fan takes on the ship, and we’ve also seen versions in the Star Trek Online game and...

... too much Linear Advance will introduce artefacts (Linear Advance avoids bulges in corners, overdo it an the bulge becomes a hole). With Linear Advance tuned retractions of 3 to 3.5 mm are generally sufficient, speeding up print times by about 10%.

Dont tighten the Belts too much, otherwise the cheap gearbox inside will be damaged (i killed 5 motors with to tight belts, before i found out that this is a bigger problem) The X-Axis can be tighten by the M6 rod in the middle ( i made the holes...