nexstar 8se 3d models
179 3d models found related to nexstar 8se.thingiverse
Customized version of https://www.thingiverse.com/thing:160391 for Celestron Nexstar 8se Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
I have a Celestron NexStar 8SE telescope, so my beloved girlfriend design this thing for me, I post this thing here with her permission. Based on ( http://www.thingiverse.com/thing:321295 ) Update: It works really well. if your printer is...
thingiverse
The Celestron NexStar 6SE and 8SE mounts are the same, except the gear cover/dovetail shroud. The 8SE shroud has a larger radius to accommodate the larger tube diameter. If you want to use a 6SE mount with an 8SE tube, you will need the larger...
thingiverse
This is a replacement for the rubber feet that attach to the bottom of the NexStar SE mounts. They are not exactly the same as the original but they fit perfectly and look great. ...Should be glued in place but they stay on to an extent without glue...
thingiverse
This adaptor plate allows to interface a Nexstar 6/8SE mount on a Celestron CG4 mount tripod. The list of needed hardware is described in the drawing. ... The purpose of the two M5 screws is to prevent the part to delaminate when torquing the M10...
thingiverse
this little thing helps you to get your objects right in the focus. it becomes especially helpful in astrophotography. just stick it over the focus-knob on your telescope and you can adjust your focus as you prefer. haven't tried it yet, should...
thingiverse
The AA batteries in the Celestron NexStar 6SE/8SE go-to telescope don't last very long, so I designed this holder to attach an external Mavic Pro drone battery for additional power. The rechargeable LiPo 3S Mavic Pro drone battery is rated 3830 mAh,...
thingiverse
Print in highest resolution and 100% infill. I cannot promise it will last, but it seems to be working fine for me. ... Remember to grease the gears.
thingiverse
Battery holder for the Celestron NexStar 6SE or 8SE tripod (perhaps also for other telescope brands / sizes?). The battery holder is designed for using 12V NiMH-Sticks. ...You can also fit in a 12V power outlet.
thingiverse
... because I was off on the calculation. The version 2 has a pattern width of 5.6mm @ 20 degrees. Bahtinov factor 175. The Celestron Nexstar 8SE has a focal length of 2032mm and an aperture of 203mm. ...The obstruction of the secondary mirror is 70mm.
prusaprinters
This is a solar filter for a Celestron NexStar 8SE for viewing and taking pictures of the sun. The glass can be picked up through Amazon for $10 at the link below. Just set up the gcode to pause for the glass to be inserted at the...
grabcad
It follow the : Celestron Nexstar 6 SE myFocuserPro2 version 3This time sized for the Celestron Nexstar 8SE telescope.Measures from wei chen who needed this model.Compared to the 6SE , this model is reinforced at the back from the motor.It was done...
grabcad
This new myFocuserpro2 bracket for the Celestron Nexstar 8SE is more compact and modeled with the specification i get from Vitaliy (Artyu Studio) : https://www.turbosquid.com/Search/Artists/ARTYuSTUDIOA big thanks to Vitaliy for his help :)It's...
thingiverse
I found it annoying that the tripod spreader (lens/accessory tray) that came with my Celestron Nexstar 8SE telescope needed to be removed to fold in the legs, and also was a little too wide to fit in some tripod carrying cases. ... So I designed this...
thingiverse
This is a bracket designed to mount a Canon EOS camera (tested with EOS500 and EOS550) onto a Celestron Nexstar 8SE mount using a Skywatcher 15cm dovetail plate, so you can do astrophotography with a standard camera. The bottom rear edge is aligned...
thingiverse
This was designed to hold a TalentCell 11000mAH battery (model YB12011000-USB, purchased from Amazon) to power my Celestron Nexstar 8SE telescope. The TalentCell battery has a higher capacity than the Celestron PowerTank, is cheaper, and is far...
thingiverse
This device allows for mounting of the stock red dot finder and a laser pointer on the original mounting rail for a Celestron NexStar 8SE telescope. ...This device is composed of 4 parts: 1) Mount 2) Laser Rail 3) Laser Rings (2 each) 4) Mounting...
thingiverse
This was designed to hold a TalentCell 11000mAH battery (model YB12011000-USB, which I purchased from Amazon, https://www.amazon.com/gp/product/B016BJCRUO) to power my Celestron Nexstar 8SE telescope. The TalentCell battery has a higher capacity than...
thingiverse
Bahtinov Mask for 8" Schmidt Cassegrain Telescope (SCT), including C8 & Nexstar 8SE
thingiverse
Bhatinov filter for Celestron 8se. Prints in two pieces and snaps together. ... Print both pieces with supports.
thingiverse
Firefly 8SE Action Camera Case. Hinge is pretty tight. After printing I used a piece of metal wire to make hinge movable. ... Also here you can find STL with Camera Size Template to make your own Cover Designs.
thingiverse
I really liked how the original THING "clipped" onto the front of the 8SE like the cover. And then, like some other designs I wanted it to split in half, partly for storage purposes and partly so that it would fit on my printer bed. I wanted the...
thingiverse
Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
... get wrapped around the mount. ...The bracket snaps onto the vertical mount arm and the hand control slips into place. Created using TinkerCad Printed using 40% infill but probably doesn't need to be that dense. Custom Section NexStar Evolution Bracket
thingiverse
https://www.tinkercad.com/things/lj8lJN8JJs6 Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: 10-25% Custom Section Fits over the existing focuser knob on Nexstar SE telescopes to provide finer focusing adjustment.
thingiverse
Inserts for Celestron Nexstar telescopes. Big Hole to Camera or Other Big Hole to "Button" type GPS Small Hole to Eyepieces with the caps on! ... A tray for the stock diagonal
thingiverse
The Nexstar control is stored on the side of the telescope mount and I find this hard to get at when viewing. So I made this bracket. ...V2 adds a bracket to allow for mounting a SkySync GPS module preventing cord rap.
thingiverse
This is an adaptation of NexStar Controller holder that attaches to your Telescopes tripod. This one attaches to your pier. This one is set up for a 7" in diameter pier, but this can be adjusted in the Solidworks files. ...
thingiverse
Remixed the adapter because the 3 screws on my Nextar 8SE optical tube are further appart. ... I suppose this might work with 5SE and 6SE