portable computer case atx 3d models

In the second case you need to use two parts from the upgrade kit to make things fit: https://www.prusaprinters.org/prints/149876 For those of you that have troubles to get the metric screws and nuts, I'd like to mention that there is a 3D...

Customized version of http://www.thingiverse.com/thing:46884 with options: perimeter -1000, qr_tolerance 0.001, per_h 10, per_w 3, tag_height 80, hole_r 10, hole_y 0, hole_x 30, case_thickness 1.8, obj 1, tag_width 80, qr_y 0, qr_x 0, corner_radius...

- make the hand rails from brass **Windows** I used CD cases for my 901-212 and 901-213. For the 901-211/214 I added 3 stl files to print a prototype for a mold to cast them from clear resin. 901-211\_windows-6mm\_mold\_frame.stl (just an...

If that's the case, we need something of a "keyhole" profile; these two variables control the square part of the keyhole. Width is the length along the X axis; depth is along Z/Y axes (remember the orientation thing we talked about), which is how...

In that case you need to ensure the gab is closed while gluing the socket onto the ring. When the ring is done and fully cured you can do another test run to see if the LED strip survived, but it is not required. If there is no visible damage,...

Similarly in the case of Heracles, when he had brought to the Greeks the doctrine of the sphere, he gained great fame, as if he had taken over the burden of the firmament which Atlas had borne, since men intimated in this enigmatic way what had...

It may be necessary to use theVinyl Template* to also cut whereRiser will be attached to the windshield and JBweld theRiser directly to the glass** Cover the dashboard with an old towel in case of drips. Mix and apply JB Weld epoxy to the...

Which I'm concerned, over heat cycles, will cause the Z lower to shift inwards because it is being squeezed by the electronics case when this happens. So I lopped off 1mm from the bottom (outward facing when installed) side of the Z lower to make...

The printed parts are actually the same, it's just the front and rear panels that are different but I prefer to keep them apart for different reasons.For most user cases, one or two dryers should be sufficient but it depends on what type of filament...

 (Not surprising, but possibly indicative of some issues with “playability” at this scale?)  Here are the things I have tried, in each case:Issue(s)Things to check:Things to try:i) My ball does not always sit still when I place it on the table, or it...

Once the carriage bolt(5) is fed through the slotted lever(1), it should stand on its own with no need for support, and adjustment should be as simple as moving it with your hand and it should stay in place on its own after adjustment.  A slip...

(Probably more variants in the future, if needed)  Print instructionsRecommended Print SettingsInfill: 15 %Layer height: 0,20 mmSupports: No Optional hardwareFor fixing the gridthis: screw 3x16 SPAX (schraubenking) - will slightly look...

This should be able to accommodate even the largest phones with cases. To maintain clearances with the lid the phone/device should not be thicker than <strong>12.8mm</strong>. Thicker devices, like AirPods, will work but may need to use the front...

But just in case any piece came out imperfect during printing, you can get the individual STL without the AIO prefix and re-print at ease.The grey color on the BVM is very dark and I've found the "Cerprise" Grey to be very close. You might want to...

In extreme cases Z-Hop can also help. It's a pity Prusa Slicer doesn't support coasting as it would make tweaking it a lot easier. If you see excessive stringing (like when printing PET-G) turn it up, but **if you have extruder jams turn it down**. I...

[NOTE: It is best to use a glue that gives you enough working time to slide the pieces after inserting all but the last border part(s), just in case…] &nbsp; *I did not need to glue my board, when I used these v6 pieces. They fit precisely into the...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

In that case you need to ensure the gab is closed when gluing the socket onto the ring. When the ring is done and cured you can do a test run to see if the LED strip survived, but it is not required. If there is no visible damage, then you did...

If you'd like access to that side door while inside the case then two cuts (colored in red) work in tandem with a built-in hinge area to allow easy opening! Step 12: Post your makes!Please post 'em! Really! Take a cameraphone photo with your dope...

I included a slightly less than and slightly more than hole on the servo horns just in case you want a little more or less throw. Some might want more aileron for example like you would get from the stock hardware kit. On the rudder you may actually...

In this latter case, the design has a small rim in the "frame" (the part with the large rectangular hole in the middle), where the bottom part sinks into to just the right depth. The lid (or cover) is printed as a single piece, and it is universal...

When it's fully assembled the helicoid bottoms out at infinity and "tops out" on the "grip_and_retainer" focus ring, while having plenty of tab length, so it's my hope that it won't fall apart on you.I think the best use case for this adapter is as a...

The wires of the LED's are guided inside of the T-slot of the vertical aluminium profile and conducted through the designated opening inside of the electronics case. A reflective screen / Light shield on the light bar can be attached if required. See...

UNTESTED but should be noticeably “better”, see notes laterChanged the nut slots to hexagonal to more securely capture the nutsSlots instead of captured nuts in the spider (similar to several other remixes), spaced correctly for M4 pitch and 0.28mm...

Also you can check out the handy discord thread about alternate use cases - for example, For the hands3: it can hold things roughly 70mm in diameter round - so a can of a soft drink...a led puck light for use as a body torch/light (using the tactical...

But in this case you still have to use a small support for just one edge. You have to print the same way by putting the model on its side. <hr /> <p>&nbsp;</p> <h3>My some other things:</h3> <p><a title="Tabletop organizer"...

In this case, it is necessary to award such a prize. Well, or at worst, it can be printed in miniature size and hung as a keychain on the keys. By the way, if someone only needs a chain, I have attached the source file for Fusion 360 <hr> ...

Unfortunately, this has to be done via a single file at a time(unless you pay for premium access) and you will have to copy it over via either a google drive, dropbox, or some other means of file transfer to your computer or printer. I do...

The order they are labelled is: starting in the front, clockwise seeing from above, and outside to inward in case it's necessary. Parts for each level, in this case, for the habitat scaled 1:40. Scales I present this model in six scales. Some of...

At the very least this will require a wet cleaning of your camera sensor, and in the worst case this will render your camera into scrap. Take care.Shooting with the tubeTo mount a lens to the tube, align the Canon lens' alignment mark with one of the...