scp 3199 by 3d models

I saw "DSLR Camera Ornament" by JayPierstorff (https://www.thingiverse.com/thing:5156802) and thought this would be a very nice toy. So I modified the parts and added a CR2025 battery holder from shusy (<a...

4/26/2020 Update: Shrunk download significantly by removing my build libraries, that was dumb, you need to build it anyway. Also tuned down mA on TMC2209's to 790 to eliminate layer shifting issues I was having. Ignore the calibration file, it's...

All pictures with 2 tricorders side by side are this project vs the 90s playmates toy.HIGHLY RECOMMEND PRINTING MAJOR PARTS WITH TEST FILAMENT FOR BASIC FITTING FIRST.Demo internals video will show this uses an adafruit bluefruit sense board, a 2.0"...

It is all based on this really cool Minimalist Hot End Fan Mount designed by Sebazzz, and here is the link to the original Ender 2 Pro - Minimalist hot-end fan mount:...

-- Jim Newton Founder, TechShop Print Settings Printer: FlashForge Dreamer Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Notes: To Print: Orient this model so the small flat surface (1/8" wide by 9" long) is in contact with your print bed,...

For my set up I scale up models by 0.5% to compensate for part shrinking. Used 4.5 mm BB thus model has incorporated 4.8 mm diameter BB guide grooves. Tensioning system Current model has incorporated 10 degree tapered surface which also acts as...

NOTE: If you only have a single garage door or car position, you can stop the homing operation of the empty position by pressing the limit switch with your finger. 2. After the homing operation is performed, the device will check the EEPROM on the...

caused by following this guide. Also check the regulations of your country/state with regards to main wiring, earthing etc. Using this upgrade guide, one is able to make the Wanhao D5S 3D printer use 1.75mm filament (as stock, it uses the 3mm...

This is a small planter for herbs or small flowers.It uses a wick out of wool or special watering wick cords of cotten which are cheap to buy online.&nbsp;First you have to put the wick sword in the bottom of the plant.Then just screw the planter on...

Start by flipping the iPad so you can see the camera. Adjust the screws so that the camera is as close to the center of the hole as you can get it. Then mount the adapter to your microscope. You will need a little fine tuning and practice in order...

Adjust Wheel - Measure Part Label === * Print the PDF file using („no resize“) * Cut it carefully * I used standard glue to fix it onto the Measure Part * And, I added some surface protection to the paper by using standard adhesive tape (but it...

I also used some parts by other publishers which where very helpful an I want to thank for. - https://www.thingiverse.com/thing:4562348 - https://www.thingiverse.com/thing:5043045 - https://www.thingiverse.com/thing:4948715 So far so good, I...

It may still rotate when forced by hand; this is OK. Snap the encoder on to the shaft, making sure the splines are oriented correctly and it is fully seated (no wobbling or gap). Slide 2@ 688 bearings on either end of the shaft and set the shaft...

This is my shot at 3d printed pendular rudder pedals inspired mainly by the Thrustmaster TPR and many other community made designs. I am well aware that the Arduino Uno and potentiometers aren't the best choices for this task but they fit my budget...

There is also a no chassis code name plate, the file is just "NamePlate"Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "BoxBackAssemRWB (OuterLine)":1) Start (Background "RWB"...

Astro Jetson, from the cartoon The Jetsons, by Hanna-Barbera. Astro is the pet of Elroy Jetson. He has a flair for dramatics and is not ashamed to cry for attention. His main form of exercise comes from walking the floating treadmill outside of the...

However, by request, I uploaded the current prototype to Thingiverse. Remember that it's not a polished finished project yet. First, watch my video about it: https://youtu.be/oHPHFjFOA3I Current status: It works and can count from 0-9 when...

The load on the movement is compensated by protective couplings, 10kg from 996 is enough. ... All calculations were performed in ideal "spherical horse in vacuum" conditions, do not take into account losses on the angular levers and friction ...

- Secondly, it features an IR receiver in order to be controlled by a standard (RC5) IR remote. - Thirdly, it also features an microphone and thus, it doubles as an FFT Music Visualizer. - Last but not least, it comes with its own web interface,...

Inspired by: SavageMine YTC, CryptoMykel YTC & DCA Adventure 3D printing wednesday, Nemisist YTC Crypto and HotRods & DCA Adventure 3D printing wednesday. A huge thanks to Im_Aesthetic and Ammarcoux for the basic designs. Thingiverse, Yeggi,...

(by editing this firmware I am in no way responsible if something happens to your printer or Home) These are simple directions on what I did. Configuration.h 626 - #define HEATER_0_MAXTEMP 350 627 - #define HEATER_1_MAXTEMP 350 628 -...

This is a remix of the fan nozzle by Mauro3D_MI (https://www.thingiverse.com/thing:5798414). Slightly wrong dimensions have been corrected, cable slots have been added and the one fan has been moved slightly to the side so that it no longer collides...

By doing so, it allows for a limited freedom (planar), while still providing a nice tight friction fit. So, when you're building a space frame, you can use a single 'hub' type, and the angles of the rods can be adjusted in realtime. That alleviates...

- Reel style allows for quick and easy deployment by attaching the end of the antenna to an anchor and walking away using a pen or stake through the center of the reel as an axle. - Holes around the outside of the housing provide choice of...

Overview This is a remix of the 'Dewalt DWP611 Thread-On Dust Shoe for X Carve' by nmackes: http://www.thingiverse.com/thing:1243484 Here's a quick list of the modifications I made: - Removed vinyl ring - Removed mounting holes for vinyl ring -...

I group my screws by thread length and if your like me don't go grabbing from your 6mm bin. The 6mm threaded length countersunk will be to long and you might break something. This adapter was designed for my Qidi XPro opening but that opening size I...

Automotive body filler, followed by high fill primer, & wet sanding were used to smooth the hull prior to being painted. Prop shaft The hole for the prop shaft may need to be carefully drilled out to fit the stuffing tube. Test fit with propellor...

We got ours at the dollar store, but it also fits the ones made by Expo. Two designs are attached: The first design has screw holes to be used on both the top and the bottom side of the design. This design must be printed using the flat side which...

Make sure there is no glue on the top surface to interfere with electrical contact.Screw the guide into the sleeve and check that it makes contact by using a multimeter on the Pogo pins.LEDsYour probe input may not be able to use the probe if you add...

This is done by pushing the button on the inside of the riser and sliding it down. (see photos, previously removed from monitor for clarity) There is a plastic cap over the hinge which must be popped off to give access to the mounting screws. Remove...