solid cube 3d models

The tank should be as solid as possible so it doesn't leak bubble fluid. My first tank with 20% infill, two perimeters and two top/bottom layers leaked -- it didn't render it unusable, but it got soapy on the outside and if you left the tank full at...

After it extrudes the filament left inside the extruder, just feed in the new spool of filament following it.Slicer SettingsFor the best looking tags, you'll want the top infill area of the tag body part of the model to be a single continuous solid...

I painted the solid bottom half black and printed the thin divider parts in player colors which gives them a nice accent, but this requires either an MMS or pausing printing at layer 5 or 6 to swap filament. These would be fine in pretty much any...

Do this for all spaces and eventually it should just lift off the base piece. This bung is solid! How does it breathe!?The mold is made so you can easily cut the lid with a sharp knife or a razor blade (whichever you have on hand). Simply put the...

Pretty much the same as v1.5/1.6 but is one solid printable part. Take care to slice supports in a way that doesn't cause them to form inside the duct.DESCRIPTION BELOW:I've spent several hours slowly chopping away at the original Satsana model for...

The lapjoint, obviously, is a little wider, which I think works better for a solid hardwood construction. How I Designed This The idea is to start with two Bezier curves, one for the bottom outline of the boomerang, and one for the top. We will move...

This lets you rule out colors that create lots of noise points and find colors that provide more solid and less fragmented lines. Finding your way back to the same exact setting is annoying and a matter of counting clicks of the button from a known...

This means that the cable does not need to be fully tucked into the main body compartment in order for the lid to close which gives a little more leeway.Potential for material savings:During prototyping I have printed the cradle with less infill...

This solid state design of light emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional lighting.This light is universal voltage capable and can be operated with 100-277 VAC, 50/60Hz. We also...

I used my MMU2 to do it on my Prusa machine, but this could also be done by just leaving out the lettering STLs, and doing a color change on the first solid layer above the lettering, so you can have the face in one color, and the case and lettering...

All the parts and motor must be properly assembled on a solid board. Make sure to provide provisions to adjust the tension of the belt. The tension should not be too tight or too loose. I use a custom bobbin ends which have slots similar to a...

So take it only as a fun. You will need printer with printing space of 240x190x190mm (Prusa MK2/3) is fine.Print SettingsPrinter Brand:PrusaPrinter: Mk2.5sRafts:NoSupports: YesResolution:0.2mmInfill: 5%Filament:Prusament PLA Galaxy Black  Notes: I...

While I may not have worked out all of the details of a Martian voyage, I believe that atmospheric mining, solid modular structures, and multifaceted power supplies could all be part of a real mission to mars. I could probably go on for another 5...

I included the solidworks file in the download if you can pop that into another CAD program, otherwise you could modify the STL directly using tinkercad or by importing the STL as a solid into another CAD package. Note that the cap holes are NOT...

When you're ready for the final feet, you can print all three at once, in correct-side-up orientation, without supports.  I printed these solid using max perimeters.      2:  Seat PostPrint this part upside down (wrong-side-up), and you should have...

This prints the hub as solid. I printed the handle at 0.2mm layer height, with 8 perimeters and 4 horizontal shells at the top and at the bottom and, for good measure (!) 100% infill. I used a 6mm brim to print the handle narrow end down to achieve a...

It probably doesn't need to be solid, maybe 50% would be sufficient, as longs as there's no strong tension on the cords and it's secured properly. Let me know if you find better parameters, I will add some as soon as I have a chance to test it on my...

This is a joint work with https://themachinebros.com/ 3D printed crossbow, capable of withstanding a tensile force of up to 6 Kgf exerted by an rubber band Video about how to shoot and reload the crossbow https://youtu.be/POFp_771bEU If you want to...

No additional charges for you, but I get a commission of your purchasesround silicone sealing cord foam whiteAliexpress:...

Update V3: Ok so I didn't realize before I make an STL I should combine the parts into a single solid, then convert to STL. So some parts may print funky. Just fixed Battery tray, need to review other parts. Deleted a battery tray with exhaust that...

Set bottom and top solid layers to zero (0) and pick a fill density and pattern that makes you smile.Printing with these infill modifiers will make the design more flexible. I found that the reduction of sturdiness doesn't bother me when I am using...

Please be nice to me ;-)Here you can print a spare wheel (for extreme inclines) for the Ambrogio L85.The model is created to be printed on a Prusa MK3 without support.I printed everything with a 0.6 nozzle, 0.3 layer height, as well as 3 contours and...

Right-click the little eye icon beside the part in the list to enable it.Print Settings:0.15-0.20mm0.4mm nozzleThe picture is honeycomb 14% and gyroid 10% both fill angle 0.Inner part: Print the inner infill part with zero top and bottom solid layers...

The Ooznest OX CNC Machine is built on the foundation of Mark Carew's OX CNC Machine from Openbuilds, incorporating numerous upgrades from the community.\nThe Ooznest OX CNC Machine fully utilizes the V-Slot Extrusion system, maintaining the original...

In this series, students learn how to use various mathematical equations to assess the properties of solids and containers. In this part, we will be using our molds created in part two to create permanent castings that can be used later on in the...

**Note 6**: I would recommend setting the infill to a **Cubic** pattern and printing with 50% infill for the **Mount**, **Riser**, and **Pressure Fits** as they will have a solid amount of applied force and torque, respectively. Especially on the...

 I also added a solid bottom to it so I could use it as the insert. I got this idea from @Dragoon_322938 who has some very cool baseball cap designs. He also had a pretty great idea of a sizer (see more about that in the print instructions). I didn't...

I fixed this by upping the top/bottom solid layers to 8. Supports are necessary for the plate only; the plate has some cutouts to make the stabilizers fit. For all other parts, they are not necessary and I don't print with them, but the bolt inserts...

In order to get a solid stripe at least two threads of the color must be threaded next to each other. If this is not done and one thread is left “alone” it will form a dot of color in the piece. This single, colored warp thread will only be on top...

The solid ones are a holy terror to get the peg bit over the hump. I had to keep filing them down because the peg kept mounding up as it scraped away from the edge. I am, however, certain the 100% infill ones (or more correctly the 4 perimeter ones)...