topology 3d modelling

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

If you're experiencing high stringing, do not worry, give it a blast with a heat gun, then a quick brush with a nylon brush and wipe down with a cloth to get rid of any remaining strings. Exterior Perimeters settingsTo ensure the best results...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

Currently, there are three models:Ebook Reader Holder (1x3):This was designed for my Kindle Oasis in its third-party case (if you want it for something thicker than ~15mm, let me know and I'll see about whipping you up a variation)1x3 footprint on...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

It Lets You See Your Model Being Built and Doesn't Obscure View. Why Make Yet Another Cooler? Cooling Plastic Just After Its Been Extruded Is Essential on FDM Printers and There Is a Lot of Choice for Cooling on the Makerbot Clones. I Tried All of...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

If you like & use my models please consider supporting my efforts with the button below. Thank you!…Please be sure to hit like & post a make, I'd love to see your prints!The Vortex series grows with Gemini! Print faster with crisper cleaner looking...

For example, if you shower pole diameter measures 22mm, try a Pole_Diameter value of '21'. Material We recommend printing this holder in ABS filament for extra durability. Versions 1.0 (5 Dec 2020) - Initial version Printing Recommended slicer...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

... THANKS! Happy printing! PS.: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders (and my apologies for the poor quality photos - my printer stands in a pretty dark corner of the room).

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

When/if I model it, I will put it on here.Have any modification requests? Contact me in the comments. I am active on Thingiverse.If you want to modify the design yourself, I can try to provide the original Tinkercad schematic on request.Update: Added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 30 stencil_pattern_element_shape = 3...

* The Ridgid adapter / switch part that you previously had to purchase separately is no longer needed, it is modeled in. You use more of the same brass strip used for the Ryobi part to create the Ridgid battery contacts. * The clips for the Ryobi...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

I would recommend all the bridges honestly. Update Jan 31 2021made the holes for the hex nuts smaller to promote better hold under torqueadded relief cut on the M6 hole, as threading may result in splitting the model on version D1resized the D1...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models) The small size and wide input voltage range of this unit make it ideal for operating Larson Electronics LED light bars, Golights and other equipment that requires 12VDC current...

If you still want to print your own loc line, I used the models from [MinyMan644](https://www.thingiverse.com/MinyMan644) found here -> [Loc-Line Fittings (1/4", 1/2" and 3/4")](https://www.thingiverse.com/thing:3268462). I strongly recommend...

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...