two panel cad 3d models

There is not yet a redesigned base, until this new base arrives, you may use the base of the initial phone mount, linked in the remix section.InstructionsPrinting mount_baseSimply print the base as shown in my print-files with the top facing...

If you are using only a single pad as your only mounting option, hold the cable holder when removing cables from it to prevent it from cracking or breaking.Dowel - you can add eithe one or two dowels to help you mount the cable holder into a...

The machine is large so the drivers and motors are a bit on the limit (I have a cooler for the drivers but in reality it is more designed to use nema 23 with the same Arduino uno-CNC shield but occupying drivers like the TB6600).In any case, with...

How To With the two wiring diagrams provided you should be able to get there. Everything connects to the DPDT (6-pin toggle switch.) In both of the diagrams (annotated & Frizing) please assume <b>the toggle is leaning to the right, away from the...

Apply glue to the holes in the triquetrum and secure on to the ends of the two filaments. 3. Dry fit the scaphoid on to the second filament emerging from the lunate and ensure that the filament length allows it to sit close enough to the lunate that...

Installation I have included in the files two installation guides + BOM for the Ender 3 and Ender 5. The Ender 3 guide should be sufficient for the CR10 & CR10S. I will update these if I can think of any further additions. Please comment if you...

I have constructed two of these. The orange one was my prototype and the teal one, which reflects the files posted here, is the improved version. I prepared a video to introduce the ukulele on Youtube. Please forgive my amateur video making and...

If I would level the bed in two months or one year it would still be 16.60 mm. If you print different material just change a positive or negative Z offset in the slicer for each material.</p><p><strong>How to use</strong></p><p>Step 1: Print the...

I also provided two “.gcode.3mf” files (one for Bambu Basic PLA, one for Generic PLA) which you can directly put on a microSD card, insert it into your Bambu Lab X1C and print from the touchscreen. If your printer is not dimensionally accurate you...

Original collet and nut produce severe bit wobble, you need a Ryobi compatible collet nut (M14 -1) and collets, zip router collets work but the collet nut does not fit Don't mount with out the router without the Two 500gm coil springs and pulley...

The MK3S does not use endstops, so I mounted my endstop to the lower X-carriage cap by drilling two holes for screws with a 1mm drill and then mounted a block on the X-Motor End for it to run into. Be careful while setting it, better to give up some...

It fits various Lego modelsWhere to buy stands?Ebay → Worldwide shippingVinted → Poland, Chech Republic, Lithuania, Slovakia, Sweden shipping&nbsp;Allegro → Poland only shipping&nbsp;OLX → Poland only shipping&nbsp;Ready To Go&nbsp;Are you lost with...

it shoots about 30 feet, is pretty small and is made out of purely printed plastic and two rubber bands (One for the trigger and one for the magazine).It requires no fasteners, or glue, and just uses printed tabs to connect the clam shell case.It...

For those two components I used regular PETG because a little flex was desirable. PLA was used for the prototypes and (after some spacing adjustments) worked well too. In fact - the final version of the components (CarbonX and regular PETG) were...

I used 0.2mm layers, 9% line infill and PLA-Matte for a paper like look.  Stabilizer(s) for magic bookshelfDo you have hard cover books?Book stack for which I used the “hard cover stabilizer” and the rubber trick to prevent any tilting from...

In the case of my i3 Mega the X-carriage rides along two shafts, one above the other. When pressure is applied to the nozzle from below, this force is transmitted onto the bearings, pushing on the upper one and pulling on the lower one. A small gap...

Nevertheless, nearly all models are avalaible in two types : full model and multiparts (usually a chassis and a turret).Note : its possible that you get an error message with some slicers for some models…. you can dismiss that and they will print...

The button isn't used in this project. The power supply is is made from two 2032 cells wired in parallel for 3 volts. I did this because 6 volts is a little high for the Attiny. Putting the batteries in parallel also allows more current for the leds....

There are versions to hold 4, 5 or 6 pens (the first two are about the same overall size). Making ChoicesSelect one of the penholder_*x.stl files that you would like to print. The four and five pen versions are almost the same size, whereas the six...

You can find a model with break - here. ---&nbsp;&nbsp;This furniture rollers have smooth 360 rotation around the vertical axis and can be used for example for your Prusa Enclosure V2 - MMU2S to make it movable around your room.The measurements of...

You shouldn't do "raft" since the faces facing down will be making contact together, once assembled to the wheel.&nbsp;Print the desired Mount- and PaddleMod twice, of course.&nbsp;Post-PrintingAssembly on the WheelBE CAREFULL: DO NOT overtighten the...

So I have two variations for you, one gives you some screw holes so you can mount the same flap that is too rigid to do its job effectively. I mean, if it gives you some feeling of security that this stupid flap has any effect on keeping debris in...

I have made the car and "lane-changers" work in two different modes, one would be compatible with "mechanical" lane-changers like in Scalextric Digital System, WOS or Advance. The other mode would be the "InfraRed" mode, in which the "lane-changers"...

The structure is optimized for PLA+.Post printingAfter printing, cut the small piece connecting the two grippers, e.g. with small scissors. I added it to make the grippers print reliably.</p><figure class="image image-style-align-center...

I've placed two 4010s on this carriage, packed close to the hotend. Now there's a catch to that: you print this carriage, you're gonna end up using my fan ducts (they were made for this). As a side note, those mentioned ducts are perfectly positioned...

All right reserved // web: http://www.RinkyDinkElectronics.com/ // // A quick demo of how to use my DS3231-library to // quickly send time and date information over a serial link // // To use the hardware I2C (TWI) interface of the Arduino you must...

Unfortunately, the bottom case must be glued together; Synyster1911 said they glued the contact surfaces of the bottom case, but I would recommend gluing a thin rigid plate to connect both bottom cases. The USB C mount is supposed to have the...

In two steps, an optimal shape is created:The first step is to pour the core. I used silicone for this.&nbsp;</li><li>In the second step, the core and an adapter are positioned in another mold and poured with resin. (Make sure there is no leak ;P...

You probably need two sets of +/- wires attached to the output terminals. Once the wires with connectors are attached to the XL-6019 circuit while in the printed housing and the output is adjusted to the desired voltage, a couple of dots of CA glue...

Some other details are also modeled after these printers, such as the belt spanner system on the X carriage. While these two systems guide their belt on the inside of the printer I decided to move the belts on the outside to get the most usable area....