3d print database

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

These keep everything in place as it should be. If you have any questions then just write to me or comment. And now have fun printing and tinkering. If you like the design, Johannes and I would be very happy to receive a like or a make. Deutsch Ein...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

electrical conduit pole. Print instructionsWhy I Built It I have an outdoor weather station that has batteries inside the instrument array. Changing the two lithium AA batteries once per year involves getting on the roof which is a PIA, so the idea...

Two versions available: > 1.3.1 Wheel + 2.2 Distance: Can be printed without support and must then be glued together > 1.3.2 Wheel: All in all, but needs support (for Overhang Angle 89 °) The axles are small and the rims fit exactly, so make sure...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

Shoulders and Forearms(https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms)Armored Plate Carrier(https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier)Utility...

Tighten lightly, and you're good to go. Print instructionsCategory: Sport &amp; Outdoors Summary Update 12 Oct 2019: The original design worked pretty well, but wasn't perfect. I redesigned it from scratch in Fusion 360. There are now three...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

Tools ==== * Soldering Iron * Allen Wrench (M3) * Super Glue * hacksaw or carpet knife Assembly ======== * Print the top, bottom, switch bracket and optional hemera bracket * Solder the two pin header to the back of the Duet3d PCB board * Fasten the...

Print Settings Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and "Twin Turbo" letters...

peeing mule on water box with solar charging and LED light Video: https://drive.google.com/file/d/1E4aU50-sGUfZatjUAsKsD0yaGoPQSH_f/view?usp=sharing Print instructionsI used silicone and resin to make it waterproof....

for those who download an try it, all i did was use m4 bolts stuck inside the ends of the tubes after going through the arms then zip tie around the threaded section of the bolt to keep it from slipping out, but do whatever works best for you, i...

By default the motion range is 2.5mm, but this can be tuned in the SCAD file. Print instructionsThese mounts should work well in either PLA or ABS with any layer height. Once the SCAD parameters are tuned well for your printer the clips should be...

Little material and time is required for printing. The "screws" and "nuts" can be pushed onto one another with a little force, the components are too small for a screw connection. I use the fan on the desk and another one to circulate air in a mold...

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

The single could be used in pairs at the junction point of the arches if desired or if your printer won't print the larger double base. I have supplied 4 different versions of the single with cable exits coming from different angles to allow for...

Truth be told, I've modeled most of the basic pieces, but printing has been slow since my printer died over the summer.) *** NOTICE UPDATE END **** Open Dungeon Tiles We're still here - we went to the mountain to beef up on Blender. Have new designs...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

The "printmode = true" with its following variables will prepare a print-ready layout of your parametered Structures. The length of each (not printable) Threaded-Rod will be "echoed" in the OpenSCAD-Console. They can be cut to exact that length. -...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so just be careful that you don't rip it off. Won't...

Regarding our parts list, we are utilizing all very common parts and easy to print CAD parts. Our system uses very basic electronics built on a common platform Arduino, but can also utilize any laptop plugged in. Our motors are very common NEMA 17...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...