3d printing action figures

For animated eye, use: * Circuit Playground Bluefruit -https://www.adafruit.com/product/4333 * TFT Gizmo https://www.adafruit.com/product/4367 Alternate is to use nogizmo_eye.stl * If using a printer that can stop and change filament, print pupil in...

Print them as I have shown in Cura, with or without supports. The vertical holes will be fine; it's the very hole on the bottom that gets stringy, but it still works. I was going to add a small cylinder in Fusion and make a pre-modeled support but...

for placing the drill holes or cable duct to where you need them) feel free to do so: https://www.tinkercad.com/things/fl1c7XRRpbD Post-Printing ========== Preparing the USB-C cable ---------------------------------- I removed the casing with the...

... drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split it into 'a' and 'b' parts. ...The two halves of the Display Base can be connected using two M3x12 screws, washers, and nuts.

So instead, I printed a separate case. Not completely satisfied with the 4 part case design, I also made a matching bottom for my case to make it easier to wire everything up. Now there are even more options. I changed out nearly every part of my...

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

I borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also, if you change the hotend, you will need to run PID tuning otherwise the hotend won't get to temperature. And the induction...

I printed the case parts on my Auxiliary Sidewinder X1 in PETG with a 0.4mm nozzle and a layer thickness of 0.2mm. Attention: Due to the life-threatening electrical voltage only persons with appropriate qualification should assemble and use the...

The motor plate/gearbox must be printed with supports. A 3mf file is provided with suggested plating and support enforcement block specifications. Supports should only be specified for the gearbox portion up to the second bearing. Removing support...

Hello Unless you are lucky ; using a precision square will show that a printed cube is not really square in all directions. Especially if you use the portico as an handle or you let a 1kg spool gently ply it all day long... Then you have to fine...

I printed the body and other parts, mounted the sensor in the sensor mount then glued the parts in place. As for the missing parts, get these from the original design that I remixed this from. ... Link to downloads for motioneyeos:...

The original is here : https://www.thingiverse.com/thing:4534090/files This tool cooling shroud seems to work : https://www.thingiverse.com/thing:2089094 First print went pretty well. For a while. Then my SKR 1.3 proved it cant keep a stable temp...

This is accomplished by printing a column of fanned-out light pipes that radiate from the LED. Continue reading below the videos! Videos: They are all extremely short. Warpcore running at warp factor 2 Warpcore Standard from Novel Mutations on...

I use this: Amazon link Some cable connector like this: Amazon link If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. I hope you enjoy it! Print Settings...

Printer Settings Printer: Migbot i3 Resolution: .2 Infill: 30% Post-Printing Assembly The Z-Axis adjustment block rides up/down on the outside of the front left leg (near the top). Inside the sliding adjustment block, two 8-32 nuts with a small...

If you're adding them then I'd recommend printing a few extra as I found the mount pins to be a bit fragile - they're only there to guide you when attaching them. Just a dab of superglue will hold the stack mounts in place. Exactly like the...

If your job isn’t the kindest, print this out and keep it with you, there’s always a worse job, like trying to live and work on this thing in the middle of a violent fast moving, constantly moving, lightning flashing orange and black sand storm you...

The alignment pegs print separate to make it easier and glue into one side of the base of bezel along with the magnets. I use superglue. The power for the amplifier and microphone board comes off the GPIO header. #Thank you! ... If you got...

(To print with the installation of a filling enclosed areas) About the hero Gabriel, 21 years old Originally from the town of Davenport A stout young man of small stature, dressed in simple but elegant clothes(or so he thinks) Characteristics Wizard...

The holes for the banana plugs and the iron holder are not included in the file but can be easily drilled after the print is complete. I did not take photos of the inside because it is pretty crowded with wires; however, if anyone is interested, I...

1) Print this out 2) Pull off the spray nozzle on your bottle of hairspray 3) Snap this into place 4) ... 5) You're done! Now, I have a little sheet of paper towel folded next to the can, and every time I want to apply some hairspray to the bed...

with open("input_data.txt", "r") as f: for i, line in enumerate(f): if line.strip().endswith(":"): variable_name = line[:-1].strip() value = f.readline().strip() if variable_name == 'pattern_element_radius': exec(variable_name + " = float(" +...

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

Bill of Materials (To build the extractor fan as pictured) Printed Parts: 2x Fume Extractor half 1x Extractor Switch Housing 1x Extractor Arm Mount 2x Tooth Lock Arm 1x Tooth Lock Arm Short 3x Finger Grip Bolt 3x Finger Grip Nut 1x Base Finger Grip...

To print a complete set of parts for the offset enclosure (To clarify, this is the area from the IKEA Lack table top the printer sits upon- to the top of the enclosure formed by a 2nd Lack table top), you will need one of each component excluding...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Judge,...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Agannon,...

Gcode Start Gcode * G21 (set to metric) * G90 (change to absolute positioning) * G28 (home all axes) * G1 Z100 F3000 (move to start height) * G1 X20 Y10 F1500 (move to start position) End Gcode * M106 S0 (turn off cooling laser) * G90 (change to...

Print both plastic parts and insert 10 heat set inserts into Toolhead body 2. Mount endstop switch into position with 1xM3x8 screw and immediatelly attach its cable. Later will not be possible to plug cable into endstop. Other end of cable should go...