3d printing filament guide

The design consists of 3 parts : the base (about 4 hours) - 12% density zig zag support and 10% gyroid infill the spindle (about 4 hours) the screw (about 20 minutes) Note : spindle has been printed with different support angle. The outer shell is...

From the original from HeroMe Gen 5 collection (https://www.thingiverse.com/thing:4460970) you will need to print: a. V6 retaining collar b. V6 air dam c. 4010-Lightweight Duct *FORWARD* d. Fan guard if you want... The mounting plate is used to...

I had already printed my design when i decided to do this. So this is a patch, that why the wiring is messy on the pictures, in the future i will post a cleaner version of the pcb with tracks instead of crappy wires...) Once my build finished, i...

# Ultimate Drawer System Designed to be the ultimate drawer system that is * printable with FDM printing * optimizable for anything you store in drawers * compatible with Thingiverse's Customizer * backwards-compatible with MarcElbichon's Ultimate...

The sensor is quite near the nozzle, but I've noticed no problems so far printing PLA at 220-230°C. You may need some spacers to reach the right probe distance in the z-axis. Carefully check if the sensor reacts before the nozzle hits the bed. The...

Print with supports, 3-4 shells, 10-15% infill (unless you want it to be dense). Post-Processing, I took a Dremel and cleaned out the grooves. I lightly sanded the front and back, to smooth out where the supports were. I then painted it, followed by...

2016/10/16 New: 2S Light Version Available for Printing Polycarbonate - a Game-Changer in the RC World! This is an exciting development that is only compatible with the previous version of 2S. 2016/10/06 New: 2S Version with Adaptation to Lipo Bold...

... Because in nearly every religion, love and forgiveness are good qualities that help society. So happy spring, everyone - wherever you may be. Much love. PS - Print these in the most ridiculously bright colors before you toss them into the fire!

There is a printable bearing race included for the idler pulley which works well (print 2 of them). You also may want to lube the spring housing interior with a teflon based lube to allow easier sliding since sanding inside the housing will be...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side of...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Judge,...

1) Print this out 2) Pull off the spray nozzle on your bottle of hairspray 3) Snap this into place 4) ... 5) You're done! Now, I have a little sheet of paper towel folded next to the can, and every time I want to apply some hairspray to the bed...

Here's what you need to print:Big Box - primary gameplay components1x Map Tiles1x Features1x Missions5x Agencies x54x Joint Ventures x41x Outcomes1x Time1x Points1x CalendarsFirst Small Box - Advancements and Planetary Samples1x...

* **Slides: sacrifice layer for successful prints** The track slides are designed with a 1-layer-thick sacrifice layer covering where the bolt hole transitions from hex-head area to round-shaft area. You can burn that thin layer out with a soldering...

- Wall height specifications determine that the charger station stand at a standard elevation measuring two millimeters off ground due strictly adherence maintained through designation provided above aligning appropriately placed dimensions ensuring...

Once the case has been printed, the headphone socket can be screwed into place, and perhaps a tiny dab of super glue to hold it tight. The same can be done on the side of the ultrasonic Mic - a tiny drop of super glue before pushing it into...

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

Only disadvantage: Ender3 only has 200x200 to 220 to 200 mm print area. The arm is too long for this Maybe a friend has a bigger printer Here is my "all-round package" with 120, 135 and 140 degree holders for the common 2kg rolls. The original...

How to make You can print all parts without support. Place on the build table as supplied. Circuitry is exactly as same as former thing named "Minimal Mechanical Digital Clock with Network Time Acquisition", https://www.thingiverse.com/thing:4931539...

You only need to print one lid for an entire stack. The idea is that you simply pull out the component boxes, unstack and remove the lids and the components are ready to go, in bowls, so your components are neat on the table. The magnets are placed...

Print all 3 sizes of each part. 2. Sand the barrel and rail supports wherever they will make contact with the barrel shroud, tank, and scope rail. I used 600 grit. Wipe the parts clean. 3. Install the shortest rail support. It should require...

The STL file itself prints flat and then will need to be bent with a slight angle in the stem. This can be accomplished by running the stem under hot water or dipping it in a bowl of hot water to soften it a bit, and then using a pair of needle...

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

Creation requires the ability to pause printing, the first time to insert the wheel, the second time to insert the nut. required pieces: 1x M6 washer (inner diameter 6mm max outside diameter 12mm max thickness 1.5mm) 1 x M6 flat nut...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: While I don't have a personal interest in modifying the grip for other versions of the...

This helper allows you to mount your sandpaper perfectly aligned to your random orbital sander. I created 11 different jigs:GLS 1ø 150mm - 8 holes ø 10mm on hole circle ø 120mm+ 1 centre hole ø 17mm*GLS 2ø 150mm - 8 holes ø 10mm on...

You'll need to take your blaster apart for installation, so refer to the Assembly section and the video linked there.\r\n- Super glue (gel kind works great)\r\n\r\nRecommended Print Settings\r\n\r\n- Infill >= 20%\r\n- Use a skirt...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.5 GENERATE_CASE = 1 baseFrequC0 = 17.4517 noteAlpha = 3 musicAxisHolderH = 2.4 crankDirection = 90 GENERATE_CRANK = 1...

When I built my dedicated printing room, I failed to notice that the switch for the overhead lights was located at the top of the rear wall, which is not very convenient. This design has 4 main parts: The Switch Plate mechanism, The Corner "Pulley",...

The V3 STL is the plate of the four printed pieces you need. What you'll need (assuming you're using the v3 files): - A type of silicone you'll use to make this, such as the one I used because it's cheap and rated for temperatures others on the...