Modified FSO Polonez WIP 3d models

Power draw of the machine was sufficient for the connector rating as far as I remember. With Fly RRF board I've also upgraded to simpler "secure with the screw" DC jack to avoid hot glue gun. I've included SketchUp files for v6 and KFB board and for...

Mid term it will be replaced by a solar tracker following the sun azimuth.For your convenience, I have created a WeatherStationOne collection including all but parts 6 and 8.End of overview common to all parts.Part 4 - Rain GaugeUpdate...

Alternatively, you may modify main body to have latches build in. Take pin/needle and ensure it can be inserted into side latches and main body. Use small drill to enlarge holes if necessary.</li> <li>Place side latch onto main body and insert...

I did use modifier cylinders around corners of the housing parts to add "brim" and prevent them from lifting. Do not use slicer's brim setting as you need the latches where the housing parts connect quite clean. Numbers For ease of printing, I've...

5Chatting with someone who has been customizing a lot of these I learned that they were further modifying the output with TinkerCAD. So I added a new tab "Non Hardhat Options" to add a button hole in the center of the tab, an option to add a...

This a a remix using STL files for clock of random1101 https://www.thingiverse.com/thing:3437127 Used and modified ESPHOME CODE for D1 mini from Alex18881 https://www.thingiverse.com/thing:4689116 Please read info they provide about 3d printing...

The probe dock was modified to fit the botton lug of the X gantry and extended a bit to match up with the probe block when it's attached to the toolhead.The probe retainer was redesigned to make it long enough to grab the probe and the backside of...

Mid term it will be replaced by a solar tracker following the sun azimuth.For your convenience, I have created a WeatherStationOne collection including all but parts 6 and 8.End of overview common to all parts.Part 4 - Rain GaugeUpdate...

I will also include a inventor file of the feed tube so you can load any cartridge you want by modifying and printing that file.* I am also considering sourcing the hardware and selling that as a package if there is interest.* This is a case feeder...

I used 2mm acrylic so I had to modify it for it to work for me. https://www.thingiverse.com/thing:3862902 All brackets for the top enclosure use M4 bolts and T nuts, I also tapped the ends of the 20x20 extrusions to M5. And the hinges and door...

If you have a modified Ender 3 that uses the 3DFused linear rails for the X-Axis (https://3dfused.com/product/ender-3-ender-3-pro-xz-axis-linear-rail-kit/) and you want to use the creality heatsink or the Micro-Swiss hotend (short hotends) then you...

That is what I did with this version of the scepter. My first scepter used a modified light bulb, a 9v battery, and some blue ant farm gel to make the illuminated crystal. This time, I wanted to do better. I decided that I wanted to try out RGB LEDs...

This mod is entirely reversible so if you decide you prefer to use the stock barrel, you can just change it out as you did before.WARNING: BY MODIFYING YOUR BLASTER, YOU ARE RISKING BREAKING IT. ...YOU LOSE OR BREAK SOMETHING WHILE USING OR INSTALLING...

While not necessary to make the kit functional, they add some fun customization options to the Maverick.Links for the other parts used in this build:Maverick N-Strike Barrel Attachment Muzzle:...

You can now attach it to your favorite printed (or non-printed) ballistic device.MOUNTING:I have provided modified encaps to add to your builds. These allow better positioning and more robust attachment points. - Thump n' Grind - you will need to...

Both are scaled up from the Ver 3 and modified to make them about the right size. Version 4 has a 19.5mm (3/4") outlet; but uses the Ver 3 cover, impeller etc. To keep it simple all the parts are in a Zip file.</p> <p>Version 5 has a 25mm (1")...

No need to remove hotend or modify/cut any parts. Just undo the belt and reinstall it with the tensioner assembly. You will need to buy some screws and nuts though. ***Bear in mind that if you use the original belts on the machine, the installation...

You can make your own with this expansion set http://www.thingiverse.com/thing:1321230 Objectives Students will understand what genetic modification is. Students will model how restriction enzymes work. Students will model gene splicing. Students...

The changes were: scaled the "slider" down by a percent, and rounded the edges scaled the "clip" down by a percent Minor changes to the base including: Changed the post diameter to 7.92mm since it was very tight getting the bearing on. Modified...

Modified the housing to chamfers. I STILL (yes still) don't recommend you build this yet. This is still un-tested as a whole thing. Its printed and looks and feels fine, but Ive not yet wired the fan up, and tested to see if it has the power to...

If wood or plastic is used you can directly drive a screw into the rod, or you can just glue it in place if you don't need to be able to change the stop plate.Cam...

Part files are provided so you can import into your 3d modelling software of choice to combine and modify to easily create your own ship designs. All parts are meant to be cross-compatible between kits. Note: because of the large number of ship...

Many parts are optional. Early test flight: http://youtu.be/IVNpG9oJvUg I modified Thingiverse user ennui2342's tricopter body, based off of David Windestal RCExplorer tricopter, to support the stronger, more common (in the US) 1/2inch wood dowels. I...

Modifying Marlin Firmware is quite easy if you know what you are looking for and what to change.So, if you want to "burn" the right Marlin Firmware in your Anet A8 1.0 mainboard or in a RAMPS setup to be able to use this design, I can help you with...

There are infill modifiers to get 100% rectilinear for the thin ends, while the main part of the arc consists of 1% rectilinear infill and two perimeters (if you're interested in the details, this will create a spring of sort in the hollow part of...

I'd have suggested modifying that but there is likely specific requirements here which involve exactness and details as specified in your given instructions, therefore will go along with what was originally set out by the person asking the original...

Although they should last about 1/3 of the time the official Ring batteries last.I have included STEP files if you want to modify anything. Remixes are encouraged, as I'm sure others could do better.</p><p>People often like to show support to...

I'm always more than happy to modify the models and post new revisions if anybody runs into snags or has an idea of ways to improve the design.&nbsp;UPDATE 3: Finally finished filling out a set of 3 modular trays, and added a picture of them here. I...

I also took the stock X cover from the Ender 3 CAD model and modified it to mount some drag chain that I also designed based on a model from McMaster-Carr. I made it a bit more print-friendly, fewer supports, and open sided with a pin so that you...

Modifying the mounting plate (drilling 6 holes, if that is not an option read about an alternative mounting solution at the bottom): 1. Print the two stencils (nf_crazy_feeder_stencil and nf_crazy_cold-end_stencil). 2. In the meantime, remove the...