battletech 3d print files

This is a remix of the smart nanoleaf replica from Surrbradl08 wich can be found here: https://www.thingiverse.com/thing:3354082 The SMART CIRCLE LED DOT is easy to print. I use black PLA for the top, the bottom and the inlet. For the diffuser i used...

A complete unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole), 3x Arm (Peg), 3x Arm Clips, 3x Brackets, 3x Rods, and 6x Hands to be printed, with 2x 608 bearings. Optionally included is an...

Print Settings Printer Brand: LulzBot Printer: Mini Rafts: Yes Supports: Yes Resolution: .2 Infill: 20% Notes: If supports are not included, there may be some limited bone "matrix" inside the actual model; this might or might not be enough to...

The printed part worked first time once supports were removed. However, holding the case together after destroying the flanges and rivet was easy: I drilled and tapped the remains of the rivet to accept a short countersunk bolt found in my computer...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

To extend the rear arm tubes, you will need: Forward (forward): L:120mm D:15mm Backward (backward): L:130mm D:15mm Printing Information for Parts 80% PLA for power elements and 30% PLA for the rest of the parts. Setup Requirements For this...

Please ensure your XY compensation is set correctly before printing, as I do not adjust for my printer. The project includes an all-in-one version, a no-duct version, and a slotted frame with glue-on ducts and braces for a full-size ducted version...

My huge thanks to both of them. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2**Rafts:** Yes Supports: Yes**Resolution:** 0.2 mm Infill: 20% **Filament:** [ Makerbot PLA...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

Additionally it was printed just out of PLA. you might get even bigger strenght with more perimeters or other materials WARNING:This hook is designed with mooring and releasing some light wight gear in mind. DO NOT use it for climbing or in cases...

(I've worn them and they're actually not uncomfortable) List of the parts needed to print: 2x Nanami_rim.obj 2x Nanami_pads.obj 1x Nanami_nose_bridge.obj The rims are perfectly symmetrical, so don't worry about having to mirror them or anything. The...

 PLACING IT ON THE WRONG LEG IS A HIGH RISK TO YOU.You could use this mechanical design and limit switch to interface with the low-voltage system, but you will have to provide the required software modifications.There are several adjustments...

Depending on the size of the equipment to be inserted in the box, it may be necessary to print more or less intermediate parts: "Body". The assembly is done by 3 threaded rods of 4 mm in diameter and 6 acorn nuts (3 at the top and 3 at the...

August 17, 2018 I added videos with Banebot wheels and improved stepper support: https://youtu.be/ayka_9WWK08 https://youtu.be/4J9OeD_G4EI https://youtu.be/0Lg4ioItwHg March 10, 2018 First garage tests: https://youtu.be/bwohv99UVjI...

The original design for the FT5 is kind of kludgey with the woodcuts and prone to vibration which loosened the X-mount for me and led to a failed print once. This redesign is ahhhmazing. My test suggest ~400mm/s linear motion is possible before X/Y...

This is a small sport hovercraft that is simple to build and decently fast and agile.Materials:2x 1407 brushless motors2x 15a brushless ESC2x 3in prop1x 9g servo1x at least 2ch receiver1x battery connector(I used an xt30)1x 3s or 4s lipo about...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: snapAxisSlack = 0.5 GENERATE_CASE = 1 baseFrequC0 = 17.4517 noteAlpha = 3 musicAxisHolderH = 2.4 crankDirection = 90 GENERATE_CRANK = 1...

When printing the lower air duct, I did not use support inside of the duct itself; instead, I used some outside. Internal walls are designed to eliminate the need for support which would be difficult to remove. The duct on the extruder holder...

... I should now be ready for action. Printer Settings Printer: Velleman Vertex Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 30% Notes: If you orient the meshes properly, supports are only needed when printing the Lower harness arm.

Consists of:- A mount of direct drive BMG BondTech extruder kit and stepper motor NEMA 42x22 0.8A.- Mounting and covering BL Touch from Creality.- A duct of dual-blowing and 4015 front fans.- Cable management. How I Designed This Autodesk...

I extruded the design to 1mm, added some fillets, and printed it in PETG. Worked the first try (instead of requiring the expected two redesigns). For those still following along, I installed the video card with the new PCIe bracket into the QNAP....

I have a modified version ready for printing, or you can simply cut out the piece that's in the way and make a new one. That's how I did it. V2: But if you want to order a new display and do some modifications, you can also just swap the original...

The entire box is designed such that if you print with 6 shells in your setting the outside walls will be solid, and the front wall will be double thick as it will take most of the hits. The bottom is flat, but has a large recess to allow you...

Our design is nested and compact, which means it takes less time to print one set. The board we use makes wiring and assembly more accessible. With an internal battery charging circuit, you don't need to remove the battery for charging. To control...

Everything is designed to print without supports. This project is a work in progress, but current state is usable.Spool Assembly:Attach tie to desired slot. I have found the slot opposite to the hanging hooks tend to position the cord ends in a...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

Assembly Once all the pieces are printed, start by running the wire through the hole in the center disc of the inner_reel so that equal lengths are protruding on either side. Thread the wires through the holes in the upper_half so that the wire on...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...