carousel horse 3d model

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

 February 17th, 2022Parts Revised:Wire GuideThere was an error in the model that I didn't catch.  Part of the base wasn't extruded in Fusion360.  Version 1.3 is still usable, but it's not what I had intended, so here is version 1.4 of...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

Ok, so i designed another one because the existing models didn't satisfy me. I also made another design myself previously, but i was still not happy. The reason is that i dont know how all the pumps are designed. - Why do some pumps have...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

You may have to do some light cleanup, but the fit of the parts should be snug enough to hand press together with no wobble. IOMarms STL- These arms are taken directly from the original wood designs and are generally sized for an IOM, but are not for...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts: Base:___________________Placeholder____________________This is the base of the...

Remove the stock z-axis tops and replace with this light bar mount.Single Mount Z-Axis Top No Switch: Same as Single Mount Z-Axis Top with no hole for the power switch. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15%...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

I also added a version of the female parts with a tolerance of 0.2mm for those who have well tuned 3D printers (see below). To know more about your Printer tolerance, don't hesitate to have a look at <strong>Maker's Muse</strong>'s videos on the...