confucius 3d print model 3d models

EN Translated with www.DeepL.com/Translator (free version)            When printing, observe the direction of the parts on the tray Assembly order 1 Place the 4 nuts (M3 square) in their housings2 Pass the...

Not counting shopping and printing time, this project took me about an hour and a half to complete. Thirty minutes of that was just waiting for the silicone caulking to dry completely. Everything I bought came from stores near me, but the components...

Key features: - low profile with 22mm (depending on T2 extender used) - integrated stray light guard - camera rotation possible - thermal isolation from camera to filter (especially handy with heated Etalon filters) - tested with a 500g camera...

I also have a light-sensitive resistor on it and plan to add a sensor at the rear and one facing down to prevent the robot from driving off cliffs.\r\nI've got plans to be able to extend the length of the track assembly by adding a third cog, but I...

Here are the dimensions for the eye module: * Length: 100mm * Width: 45mm * Height: 30mm All the parts were printed using ABS and then treated with an acetone vapor bath to give them a smooth finish. After the vapor bath, I drilled holes in all the...

The pieces I made to hold the bumper buttons haven't been printed or tested by me yet as I used hot glue in an earlier prototype piece. You can use just hot glue to hold them, but this may risk pushing them loose. The contact rings on the SparkFun...

Before you start, if you are planning on printing it first and installing it after, make sure you have installed the mount bracket for the stepper motor/extruder. The mount bracket is made to use the mount screws for the two upper rollers. If you...

https://www.ebay.com/itm/3mm-Coupling-Motor-Rigid-Flange-Guide-Shaft-Coupler-Motor-Connector/232597820268?ssPageName=STRK%3AMEBIDX%3AIT&var=532004818119&\_trksid=p2057872.m2749.l2649 3mm 2x 18350 battery...

I speak up now only for the next generation of silent sufferers, which from what I've witnessed from the inside is the 'True Normal'.) I kind of feel like printing mostly Sixteenth and Eighth notes and rests, to suggest high energy and rhythmic...

- PrusaSlicer recently implemented a change for "Elephant Foot Compensation" that changes how the first layer is printed so that it isn't wider than subsequent layers. - I recommend setting the value for this at .1mm, because I found this change to...

Comes in 32mm and 75mm Scale - PreSupported option available (Actual printed size is 65mm and 150mm respectively).   An elite fighting duo that are legendary amongst the front line and special operatives of The Golden Griffins. Just the sight of...

... Designed so everything can print flat and help minimize supports that would be needed. The extrusion brackets perform several tasks: Hold a 2020 extrusion to the gantry by way of the Makerslide rail. The 2020 is/should be tapped for M5 threading.

I made it that way just because it can be printed without supports. The three holes are used to line up the two pieces. Drill them out a little and you can use a short piece of filament to aid in the process and just trim them off flush with that...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

-Customizable pipe cap https://www.thingiverse.com/thing:4795549 ...this thing -Customizable Pipe Cap "Cover type" https://www.thingiverse.com/thing:5150957 -Customizable Rectangle Pipe Cap https://www.thingiverse.com/thing:4875215 -Customizable...

You may print out and use any settings desired, while 2_Upper_center_font defaults automatically to write/Letters.dxf if user forgets specify a preferred alternative. 2_Upper_center_size equals fifty-four with two spaces from upper edge due being...

It consists of a "flying" assembly (2 parts) and a ground assembly (3 parts) which should print all together in less than an hour. You also need two pieces of string (ideally strong, non-elastic and very thin) or wire and a standard-sized tealight....

... screws from the PCB, make sure the PCB is in place, put the lid on top of the body, and tighten everything together with 4 M3x12mm screws. Contributions are appreciated - it took a lot of time to get the design made in Fusion360 and test prints.

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

I would recommend printing with 100% infill. Included in the download is the sketchup source file for your own customization (Hint: I always include my source files). UPDATE!!! I still need to determine the pinout. I will post it up here once I...

Print the transparent rings ("Ring") with a 0.6mm nozzle in vase mode. I used PETG; the rings were flexible enough to be slipped over the spools. For lighting, I used a controller that adjusts lighting effects based on the music. Just search for "led...

If you're not using a hole that has been cut, then there is a cover so your nutrients don't get light.Use a 51mm hole saw and you have a water filling hole and a hole for the water level gauge.General printingEverything is aligned for printing...

Geoff Gregor's notes on his R2a modification state: "Summary: Nut pocket slightly bigger, screw head pocket much smaller, less damage, no more slop, screw stays aligned for happy printing (hopefully)." After struggling with a squeaking belt on my...

You'll need to print a grip, four jaws, base, top and top center. The "Big Screws" top goes with the V0004 Top Center and the normal top goes with the V0002 Top Center, although it's not absolutely vital to get this correct. 1- Push an M3 nut...

This is an interference fit, you may need to sand it a bit to get it to fit, my test print barely fit on my carriage. I used a large nozzle with PETG as the test, which tends to skew the dimensions a bit, if the fitment is loose/tight let me know, I...

With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode. The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you...

Use a screwdriver to adjust the tensioner, and with the mirrored version, you need to pull the filament lever to access the screw.Screws neededTool:Buttonhead or cylinderhead4x M2.5 x 6 or M2.5 x 81x M3 x 30 or M3 x 28 (For the mirrored version you...

I've tried increasing the print speed to 150%, no layer offset !, there's probably more to do. For assembly: I bought my motors online (MKS SERVO42C NEMA17), they were already pre-assembled and calibrated. So they could be used immediately. To...

UPDATE 2019-04-26: added redesigned chain for easier print "Chain Whole V3" and fixed bug, both sides needs equal number of chain parts, old design has one missing chain part. Old design for some people fused too much, couldn't get it separated. New...