counter rotating edf 3d models

This allowed the rods to be rotated to a matched direction where the gantry slid the easiest. I did the same thing on all the bearings too as you see my labels and hash marks lining them up where each pair slid...

Effector carriage: v-wheel-top-clamp - mounts a full sized delrin V wheel, clamps with 4x M3 bolts to the carriage body Carriage_Front_bdige_rotated & Carriage_Rear_for_Longer_Stepper - mount two mini v wheels, and the motor for either a Titan or...

Spring V2.stl - IMPORTANT You need to rotate this 90 deg so the two spikes (pillars) are facing upward (PLA). Bearing.stl - Print as is. No supports (PLA). Spinner type A.stl - Print as is with supports touching build plate only. Maybe infill 98%...

By rotating the motors, I could make the design narrower and get back that lost print space along the X-Axis. My design faces the two motors towards each other straddling the chrome rods on the X-Axis & offsetting them so they can be attached using...

Update : there is now a version that can be mounted on the X carriage of the Prusa Mini :) Hi !!I'm a jeweler and use my beloved prusa MK3s to design invented custom tools for my craft. The visualizer challenge, encouraged me to create...

Might need a hammer :)Step 2: Added 5/16 hex nut and tighten down.Step 3: Press-fit 608z bearing on both sides of the bearing roller.Step 4: Assemble the base and roller.Step 5: Press-fit the 5/16 nylon locknuts into the end cap of your choice.Step...

This print contains a latch that prevents the tube rotating and helps with the strength of the hold. The main version i made holds a tube .625in(15.875mm) in diameter. However, you can use the STEP or Fusion 360(with parameters) file to change...

When the Voyager 2 probe reach Uranus, the system where pointing its north pole of rotation to the Sun. Sometimes, because the south pole or the south hemisphere are defined as the one pointing to the south of the Earth reference, and the right hand...

If you then rotate the spool so that the filament passes through the spool "from below" (see photo), you also avoid unwanted unwinding of the filament on the spool. I like the ingenious click function, because this allows the distance between...

I cut low on the bottle, but only because there is a shoulder making a straight cut easy on an otherwise very profiled bottle. After cutting, touch and rotate the newly cut edges on a hot surface of sorts, e.g. an old frying pan. It should be...

It also requires no drivers and this mount doesn't require rotating the display - it is 100% plug-and-play. Here's a link to my modified Pi3/4 case with a V slot mount I'm using: https://www.thingiverse.com/thing:4536100 You need at least a 150mm...

... one of the carriage belt clips) and a nozzle duct. These STLs were exported in the "in-use" position and should be rotated 90 degrees to their flat side prior to printing. ...I recommend ABS for for heat resistance, but it seems to work fine in PLA.

So I remixed the model, and opened a whole on the cover, enough for the probe mount not to hit the motor cover.Finally, I wanted to do some cable management for the sprite pro cable, which is known to be prone to fail unless you use some strain...

I found that a set screw alone did not work too well and the lock tended to rotate in the adapter while riding, as the shackle of most locks is hardened. What I found worked better was using epoxy to glue the adapter to the lock in conjunction with...

So please comment and post your results. The rest of the models are designed to print with support "touching build plate" and do not need "support everywhere" Depending on your printer and cooling of course. Files "should" load pre-oriented for best...

If wall mounted you can rotate the screen to see it easier from above - the screen insert is omni directional. If you want to mount the case just cut away the 0.2mm layer that covers the hole for the bolts. ### Disassembly notes If you need to...

 The CAD was fun, and occasionally maddening (rotation of the cutter body to get the lower indentation was really frustrating).  But, that's par for the CAD course.  I was able to model each part in about the time it took to print the...

I use Prusaments Jet Black and Orange PLA.Base color:Baseplate:                   0,2 layer height30% infill3 contoursrotate bridging to 45°no supportsBracket:          ...

Do not over torque, or you will break the cleat.SkinnyStart by adding the heat set insert into the bottom section of the hanger.You can now screw this part into the top in either a flat or rotated orientation.Add the captive M3 nut and bolt. Do not...

I recommend opening up the holes by piercing them with a razor knife (see photos), and rotating the knife blade to carve out the fill. Do this for both sides of each hole to ensure a clean hole. The instructions below assume you have already done...

This part could potentially be laser cut from acrylic, or another sufficiently rigid 3mm material that can withstand the nearby heat of the (insulated) heated bed plate.Assembly stepsDisassembly of the Super Racer and assembly of the new frame,...

Nitrite is always below 0.2mg/l (ppm). The models should be printed in the orientation of the STLs (maybe rotate the case 90° around Z). All models can be printed without support The baskets can be printed without support, assuming your filament...

The first modern athlete to throw the discus while rotating their entire body was František Janda-Suk from Bohemia (present Czech Republic). He developed this technique by studying the famous statue of Discobolus. After only one year of developing...

It is still a very desirable piece of beloved retro tech to this day!This mini-monitor design was modeled in 3DSMax for 3D printing to use with an 8 inch LCD Monitor 4:3 IPS (1024x768) Screen, and incorporates inputs for HDMI, VGA, AV, BNC Built-in...

 You may need to rotate these to print them in a way that makes sense.  Generally no supports should be needed.  Print the top part upside down and the bottom part right side up.  The left side will print fine with the cut-out for...

A: About -40mm X and -10 Y Q: Can I rotate the Hemera 180°? A: Yes, but I haven't tested it yet. Q: How do I wire it? How do I change firmware (etc.)? A: Sorry, but I won't explain that. There are many tutorials on the net for this. ...Even for the...

The gear train is designed to rotate the hands of the clock at a rate of one revolution per minute. * The stepper motor is a NEMA 17 size motor that has a step angle of 1.8 degrees. It is connected to the gear train via a shaft and is controlled by...

I haven't tried it. Use black filament, of course. Finally, and most crucially, rotate the part in your slicer to align the bottom layer lines along the long axis of the plate. See the screenshot if you're not sure what I mean (it's looking UP at the...

However, in some cases a switch might be nice to have too in case you tape it to a rotating rod to create an orb or something like that. Print Settings Printer Brand: RepRap Printer: ...

The options used are as follows: - Corner num: 1 - QR tolerance: 0.05 - Perimeter: -1000 - Tag width: 80 - Tag height: 80 - Object type: 1 - Round corner: 2 - QR data: [1,1,1,1,1,1,1, 0...