cr 10 enclosure 3d models

356217 3d models found related to cr 10 enclosure.
CR-10 Enclosure
CR-10 Enclosure
thingiverse

This is primarily a remix of Kiayoto's CR-10 enclosure. I removed the lower section of that enclosure and modded several pieces of the original. I had printed all of the original parts then made adjustments to suit my needs. I also modded the...

CR-10 Enclosure Thermometer Holder
CR-10 Enclosure Thermometer Holder
thingiverse

This is just a holder to slip in a temperature gauge and attach it to the CR-10 enclosure from 3DUPfitters. (It should work on DIY enclosures as well.) Its designed specifically for this thermometer-- just slide it in. Its designed to attach...

CR 10 ENCLOSURE - LIGHT series
CR 10 ENCLOSURE - LIGHT series
thingiverse

CR 10 LIGHT Enclosure UNTESTED All are just recommended dimensions, same goes for the panels! One CR10 version accommodate the CR10 with the spool on top of the frame, second reduced on high with 100. This is just an example! Feel free to make...

Creality CR-10 Enclosure
Creality CR-10 Enclosure
thingiverse

Designed for the Creality CR-10 A parts list is in the included PDF. ... To seal up gaps I used Foam Window Seal can be found at a home improvement store ...

CR-10 Enclosure
CR-10 Enclosure
thingiverse

I did a fair amount of searching and wasn't satisfied with the cost or design of several of the enclosures available for the CR-10 and other larger printers, so I decided to design my own. This enclosure is fully-customizable and can be scaled up or...

CR-10 Enclosure
CR-10 Enclosure
thingiverse

It's a fully printed enclosure for the CR-10! I had tried ABS and nylon on the printer before with some pretty bad warping. The printer can do it, it just needs the heat to stay around the part and not float away and make the apartment warmer. My...

CR-10 Enclosure Parts
CR-10 Enclosure Parts
thingiverse

The Wood Piece Sizes are as follows: Front/Back - 18in x 25.5in (Door is however big you want it to be) Right Side (Front) - 12.5in x 25.5in Right Side (Back) - 11in x 25.5in Left Side (Front) - 12in x 25.5in Left Side (Back) - 10.5in x 25.5in...

CR 10 ENCLOSURE - SUPER-LIGHT series
CR 10 ENCLOSURE - SUPER-LIGHT series
thingiverse

CR 10 ENCLOSURE - SUPER-LIGHT series UNTESTED Use 4mm plexiglas sheet. Filament and Cable WINDOWS comes also in a split in two versions, allowing to mount the sealing material - sponge, texture... etc! ... DESIGN TO PRINT WITHOUT SUPPORT - by...

CR 10 S Enclosure
CR 10 S Enclosure
thingiverse

... For 2nd door need to print all additional parts - door and hinges) Print with support and skirt. Pictures are from the first design - 2 mm walls. Second design come with 3mm walls https://pinshape.com/items/44114-3d-printed-cr-10-s-enclosure

CR-10 Enclosure Hawk Filter Parts
CR-10 Enclosure Hawk Filter Parts
thingiverse

These are the parts for an enclosure I made for my CR-10. It uses cheap activated carbon respirator filters by Hawk. This dramatically reduces the smell of the fumes of ABS printing for me. This filter set up is in no way a complete filter system.

Parametric Hinge CR-10 Enclosure
Parametric Hinge CR-10 Enclosure
thingiverse

Customized version of https://www.thingiverse.com/thing:2187167 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2187167

CR-10 MOSFET Enclosure
CR-10 MOSFET Enclosure
thingiverse

An external enclosure for the MOSFET from in the CR-10 control box. The two halves are zip tied together. This is one part of a set of parts. The goal for this project is to place all of the internal components on the underside of an Ikea Lack table...

CR-10 sMelzi Enclosure
CR-10 sMelzi Enclosure
thingiverse

An external enclosure for the sMelzi motherboard from in the CR-10 control box. The two halves are zip tied together. This is one part of a set of parts. The goal for this project is to place all of the internal components on the underside of an Ikea...

CR 10 S Enclosure - metal frame cabinet
CR 10 S Enclosure - metal frame cabinet
thingiverse

CR 10 S ENCLOSURE METAL FRAME CABINET See also: https://www.thingiverse.com/thing:3233857 or https://www.thingiverse.com/thing:3230158 SQUARE PIPE 40X40X1.5mm STANDARD CR 10 S - No alteration to original - out of the box design! UPDATE 31 OCT 2018...

CR-10 Enclosure clips for Home Depot plexiglass
CR-10 Enclosure clips for Home Depot plexiglass
thingiverse

Clips to hold plexiglass in place as part of my CR-10 3D printer enclosure. These clips are designed to work with 0.093 inch thick plexiglass sold at Home Depot. one bottom clip that is flat (for bottom) so that the plexiglass can rest on flat. ...

Cr-10 Max Enclosure PSU ventalation
Cr-10 Max Enclosure PSU ventalation
thingiverse

This bolts onto your PSU cover so that you may add PVC pipes leading to the outside of your enclosure. ensuring your PSU gets cool air and not recirculated hot air. This is if you use an enclosure. ... I added a .DWG file to the download to make this...

CR-10 2020 Enclosure Guides
CR-10 2020 Enclosure Guides
thingiverse

These are designed to accept 0.20" foam core board.

Acrylic Top Mount Filament Spool Holder for CR-10 Enclosures
Acrylic Top Mount Filament Spool Holder for CR-10 Enclosures
thingiverse

Although this was designed specifically for our CR-10 enclosures, they should work on any top mounted enclosure for any printer, or you could put it on a shelf above the printer. To make this you'll need thick 1/4" acrylic of any type, and a 1.5"...

Cr-10 Melltorp Ikea Enclosure
Cr-10 Melltorp Ikea Enclosure
thingiverse

I found this on a google search for a CR-10 Enclosure. This is not my design! ... Original design credit goes to: Cscott on GitHub "https://github.com/cscott/3d-melltorp" Assemby Instructions: ...

CR-10 120mm Fan Enclosure
CR-10 120mm Fan Enclosure
thingiverse

CR-10 Enclosure. Remove all 3 Internal fans, Including the Power Supplies fan. Remove top cover for optimal cooling. Found best option for mounting the MOSFET was to use mounting tape. Mounted Power Supply using Mounting tape. This IS A...

CR-10 Ikea Melltorp Enclosure
CR-10 Ikea Melltorp Enclosure
thingiverse

I found Jackson238's thing for a CR-10 enclosure using larger Ikea tables, but did not like the use of magnets to hold the acrylic windows on the structure. As such, I took inspiration from the original designs and remade them in Fusion360 to...

CR-10/CR-10S Lack Enclosure
CR-10/CR-10S Lack Enclosure
thingiverse

This is a group of components to make an enclosure out of 2 Ikea Lack tables, and 0.18 inch thick foam board from Dollartree. The front doors open and slide back into the cabinet for easier access to the printer. It's still a work in progress. ...I...

CR-10 3D Printer Enclosure
CR-10 3D Printer Enclosure
thingiverse

A 3D Printer Enclosure that can fit a Creality CR-10 or any smaller 3D Printer / Device. ... - Frame is made from 1"x1" wood - Piano hinges are to be used for the doors - Plexiglass is used for the front panels to keep the printer visible while...

CR 10 (and CR X) TV Enclosure
CR 10 (and CR X) TV Enclosure
thingiverse

This is my new enclosure

Electronics Enclosure CR-10 Style
Electronics Enclosure CR-10 Style
thingiverse

This is a electronics enclosure styled like that of the Creality CR-10's. The enclosure is accessible from the top, the sides and screen are "hinged". This was one thing I did not like about the stock one from Creality when I wanted to make a change...

CR-10 table top enclosure frame
CR-10 table top enclosure frame
thingiverse

https://youtu.be/Ok9uSThp73A Update : 2019-07-15 1) Air filter / scrubber : https://www.thingiverse.com/thing:3749365 Update : 2018-03-12 1) 2 and 3 are 38mm short, uploaded correct files to match assembly guide Update : 2018-01-02 1) handle_washer...

CR 10 S - Filament enclosure - moisture protection
CR 10 S - Filament enclosure - moisture protection
thingiverse

... - moisture protection !!! NEW DESIGN! Update 18 OCT A new version of the enclosure - with a different entrance angle - to prevent tension on filament when is used more than half of the spool! Feel free to support my projects!

IKEA Lack Enclosure CR-10 Mini Update
IKEA Lack Enclosure CR-10 Mini Update
thingiverse

Searching for an enclosure for my CR-10 Mini to print PET-G and ABS, I came across this: https://www.thingiverse.com/thing:2864118 A beautiful and simple solution, but it won't work for my CR-10 Mini because it was too short. I decided to make a few...

CR-10 Spool Holder for Enclosure
CR-10 Spool Holder for Enclosure
thingiverse

I design this thing for hold the spool inside my enclosure. I've got two different diameter of spool so I need a unique adapter. The spool holder supports spool with an internal diameter of 50 mm to 70 mm. ...I'm using the bracket included with the...

Modular 3D Printer Enclosure (CR-10)
Modular 3D Printer Enclosure (CR-10)
thingiverse

I designed this enclosure for testing me up on ingeneering... holly crap i'm far from the goal !! Printing: connectors was designed to fit to 30x30 profile M6 tappered in center. Any material a bit stiff would make the job. Extruded profile was...