dickbutt 3d print file

The screw-on spacers make it very easy to print new sizes and switch them out.\r\n\r\nAnother feature is that all parts can be used as either a top or bottom piece. I've tried to include all variations you might want, made for 3mm...

They are intended to be printed in a slightly flexible material like TPU. You could also use hot glue or similar, but only after you are happy with the focus! ## Parts needed - Above linked camera (maybe 2 in case you break one) - A few M3...

... why I think I have such poor colors and so much diffusion in my photos. Once the pinhole was made, I cut it and taped it to the backside of my printed adapter with duct tape that I then covered with electrical tape (to avoid internal reflections).

(At least in my setup, if the original z-axis endstop was used, you could wire this in parallel as a backup, possibly.) The part is best printed in ABS, PLA will warp over time. Instructions Use...

I didn't have the belt tensioner for it and since other printed belt tensioners I tried had failed, this is what I came up with. So far it's solid as a rock. Comes as 2 parts, the main tensioner block and the optional faceplate which attaches to the...

... (about 7-8 cm each) some soldering skills. **Edit:** Added original adapter battery rail ### Print Settings --------------------------------------- **Printer:** Anet A8 **Supports:** Not required **Resolution:** 0.2 0.32 for the lid **Infill:** 20

Print and remove support material from case 2. Optionally, drill a hole into the side of the case to install para cord to use lanyard 3. Install Buttons and switches - x-acto may be needed to remove material from case for button to fit 4. Install...

PLA in my opinion is not resistant enough (humidity, temperature etc.) The logo and the wings are colored in orange and silver. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: CPE...

The print itself is only a case and a lid, but I thought it may inspire some other creative invention. I apologize for the poor quality of the video and my gross fingers. It was really hard to get the camera to recognize the led screen because of...

To build, just print two ears, then attach the 450mm lengths to the tabs on the ears with t-slot nuts. It should be pretty self explanatory. m3x5 screws should do the trick, but if your parts shrink too much a washer may be useful to ensure a tight...

This kit is presupported, but also includes unsupported STLs for those who want to print in FDM or would prefer to handle their own supports. ...If you feel inclined to support my work (and get access to previews of upcoming work and voting rights to...

(Note that I have an adjustable voltage on my control board, but make sure your fan matches the voltage for your system.)- HEPA Filter such as [Nispira True HEPA Filter Replacement with Activated Carbon]Parts from Voron BOMParts here are already...

After numerous requests, I also included the Z-probe for the Bl-touch in the gallery photos.Below is a guide with very simplified photos in Italian and English versions, and at the end of the article the settings used in print (at least for me.) Good...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: While I don't have a personal interest in modifying the grip for other versions of the...

A complete unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole), 3x Arm (Peg), 3x Arm Clips, 3x Brackets, 3x Rods, and 6x Hands to be printed, with 2x 608 bearings. Optionally included is an...

... 2 with the 35mm long 2mm diameter pins. Next start pressing the 42mm long 2mm diameter pins into the holes in the out sides of deckbox part 1, align the latch and finish pressing in the pin. See image below for a section view of the assembled latch.

Required parts: GT2 Timing Pulleys 40 Tooth 2GT Synchronous Wheel Parts Bore 8mm Aluminium Gear Teeth Width 6mm - 2 GT2 Driver Belt 860-2GT-6 Timing Belt in Closed Loop Rubber L=860mm W=6mm 430 Teeth - 1 (note: not compatible with E10 or CR10 due to...

Strengthened the nose of the vehicle by printing it in Ninjaflex 70% infill or ABS. 6. Created a new FrontWheelHub that allows motor wiring to enter at the correct spot. 7. Added hooks for motor wiring in the front part. 8. Stiffened the pushpin and...

__Update 20th May 2018__ Added a different, low profile pen holder, embedded in a fake cockpit: this is exclusively for aesthetics, and print as a single object, however it's also available on...

Because there are no symbols in the other three statues it is difficult to identify them, and their names are indeed a vexata quaestio; according to Raffaello Borghini (1584), what they were actually called depended entirely on the oral tradition...

https://kc9on.com/product/fox-hunt-offset-attenuator/ ###What is what### To use this case, you'll need to print the cover and one of the cases depending on your choice of connector. FoxhuntV5C.stl has no antenna outlet for you to modify it to your...

I wanted to be able to pop this item on and off when needed so I didn't want to use hardware, I've created some spring clips on the parts - safe to say that despite my best efforts prints this small will always be fragile and these clips are no...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

 The only repair is replacement of the hammer, as epoxies and glues will not hold.I printed this using Prusament PC Blend, as this hammer needs to withstand some serious punishment to actuate the gas valves without breaking.  The PC blend...

The printed part worked first time once supports were removed. However, holding the case together after destroying the flanges and rivet was easy: I drilled and tapped the remains of the rivet to accept a short countersunk bolt found in my computer...

this is an afterburner direct drive mod for the "tronxy x5sa pro" currently the e3dv6 hotend and the dragon hotend are supported In Y axis you lost 10mm print space these things are needed for the afterburner: Cap screws M3x6 2x M3x8 3x M3x12 2x...

Could not be happier. Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Prusament PLA ivory white Notes: Supports for the pushers so that the gear teeths are near perfect. ...

Stock - this is a multipart stock, the front part needs to be printed out as a left and right (mirrored), you can either just use the 'holes' version to do a similar style to the rest of the Trigger, or you can use the 'Heatset' side to use M3...

More suggestions==================== I recommend printing the socket adapter and the snap style arm in ABS for proper flexibility/operation. PLA may be too stiff for them to work well. Also, depending on your setup you may want to use a brim on the...

Creation requires the ability to pause printing, the first time to insert the wheel, the second time to insert the nut. required pieces: 1x M6 washer (inner diameter 6mm max outside diameter 12mm max thickness 1.5mm) 1 x M6 flat nut...