iris models

Note: dimensions are in metric system (in millimeters, mm) and the model adopt A4-size paper sheets (not US-letter). <h3>Assembly instructions</h3> For the 3d printing, we used white resin for both "pointer" and "pointer+wheels". Concerning...

While his drinking-glass method worked for me, I could not get the parts of his model to fit together well, because my printer does not appear to be tuned well enough. Note that the guide is all Denny's work, refined by him in many months. My...

First of all, this is a non-commercial print, this means you are not allowed to sell files or prints of this model. Not that I neccearily would have anything against it, but it would be nice not to find this for sale on etsy... This project will...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

I have no immediate plans of adding a mount for a counterweight because everyone will find differently shaped ones _____________________ **Edit: ** Added an adjustable version of the speaker caps and a locking buckle ___________________ I wasn't...

&nbsp;- INCOMPLETEAdd variation with looser tolerances so pots can rotate freely - INCOMPLETEAdd small washer to fix noise issues some have experiences - INCOMPLETE&nbsp;As with any of my models, feel free to message me with any questions or...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

Durch die strukturierte Beschichtung erhält das gedruckten Modell auf der Unterseite einen schönen, strukturierten Look. Je nach Bedarf kann nun zwischen glatter oder strukturierter Oberfläche gewählt werden. Rändelmutter M3 / Große...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

AnyCubic Photon Heater with Optional Light Models for for the Left or Right panel For the fan I turned it around after I found it not blowing outward. Double Check You use the right top and back that go together. Don't do Like I did in the...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

Make sure to follow me to get a notification when it's uploaded!*** ------------------------------------------------------------------------------------------------------------- ###READ BEFORE PRINTING!### * First of all, this is a non-commercial...

&nbsp;READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

The XIAO is also able to be soldered with castellated holes for a low profile.KeyswitchesI designed this to be compatible with Cherry MX 3 and 5 pin models. These are easily accessible in packs of 10 or more.Circuit BoardI designed the circuit board...

The VR Box comes with pads that may fit your need here. Even if my model provided screw holes and additional holes to fit the screwdriver through, I do not recommend using them. The pillars the screws were originally drilled in are most likely...

&nbsp;You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid. &nbsp;This can be...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

* IMPORTANT - please note that i've not printed this version myself, but the CAD models check out and everything should fit together. If you find any issues please let me know in the comments. 9th January 2021: * Revised 'top.stl' - Remove...

I'm slowly printing this work of art so I hope to eventually show a working model. If you print it and find something doesn't work, please report that and I'll try to fix it. Also, if I goofed up the maze and there's no way to solve it, that would...

----------------------------------------------- MATERIALS ------------------------------------------------------ - Raspberry Pi Model 3 B (This is what I used but really any micro-controller can work) - Breadboard - Mini-Breadboard - 10K Resistors...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

This left us with our final model of our ghost clips.&nbsp;Assembly Instructions:Create center rectangle centered on the origin&nbsp;Set as construction geometry&nbsp;Add smart dimensions to constraint box&nbsp;Add construction lines for where arcs...

2x 3D printed pulley wheels 2x (or 4x) 3D printed conduit couplers (depending on how you are doing the conduit) 2x 3D printed wing push brackets (based on your plane model) (For any non-symmetrical push brackets, you'll need to print a mirror...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...