joyetech support 3d models

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.No supports required.Superglue the valve...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

I appreciate the opportunity to help and look forward to continuing to support you in any way I can. If you have any feedback or additional requests, please don't hesitate to share them with me. Your satisfaction is my top priority. Thank you again,...

If you have problems with the quality of the thread, you can "refresh" it using standard metal M5 bolts and nuts with 0.8 mm thread but I made such high tolerances that they should screw easily with hand right after printing.Do not rotate the nuts -...

Fixed an issue where the original design allowed spacing between where the support bars joined the 60mm smaller diameter ring, this caused the part to fail instantly under minor stress. I have thickened them up for increased strength. However do not...

... 4mm and length (l) of 35mm. Please check below assembly video of the Hobby ProBox that is just a little bigger as the K-Team SuperProbox but the assembly method is the same.    Assembly Video SuperProBox   Thank you for your support and have fun !

You can always just run a 1m long cable directly to the front USB port, but then it will be occupied forever, and you will always have a cable dangling around your machine.The hub can be found here: https://aliexpress.ru/item/1005005887148469.html As...

I'm even powering the RPi from 5v from a spare endstop pin off the Mini RAMBo - who has 3hrs to same-dayAmazon' yet another USB charger ? No metal fasteners needed (the MK2 comes with an extra 12mm M3 screw to replace the stock 10mm one as part of...

Now you can have a morphing table, by mixing Ikea with 3d-printing. The goal of this design was to re-use all of the Ikea parts, and also to use as few extra parts as possible: You only need some glue or 6 small screws and optionally four felt...

Parts / File Overview --------------------- * Standard Dogs * Filename: StandardDog[OptionalModifier]_Height_[OptionalTaper].stl * 25mm diameter top * Various heights available * Available as solid dogs, with a throughhole for M6 screws, and / or...

In case you lose track of how many printers you have or just want to dress them up a little bit.Supports are painted on the inside and easily removed.Quick and easy printDesigned on...

However, the aim was to get this iteration published in the meantime so it will probably be developed as an add-on unit.This future addition will thus enable illumination of the job in hand, be it soldering, 3D printing or anything else requiring...

The file body.stl has to be printed with supports. The files right_ratchet and left_ratchet.stl have to be printed with 100% infill. Links: Github Wiki for Picaxe code and pcb files: ...

(stay tuned) On the right side of the lack instead there is the drawer that contains the USB transformer and the connections of the electrical contacts and a second drawer that contains 1 raspberry 2 modules of 4 relays and 2 esp8266 boards For now I...

* Weight: Actual 3D Parts: - Hotend-cooler (PLA/PETG & high resolution & supports) (17g) (original wire connection from left side) (print with fan side bottom) (fits to original carrier) - Hotend-carrier (13.3g) with mounting base for direct...

Make sure that you position the square thoroughly in the clip, so that it doesn't look out in the front but supports the clips so that they don't fall off. Group the parts together.</p><p>Now we finished the part design and you can 3D print your own...

In the factory hotend, the stock thermocouple is not supported in the Lerdge firmware. Being that I'm a big fan of the screw in style versus the glass thermistors I needed to order a new MK10 heating block from Amazon which has both 3mm & 4mm screws...

... with 40% infill. Clamp printed at same settings but 100% infill. You don't need any supports if you orient things correctly (body with smaller hole on build plate, bushing with larger end on build plate, clamp with small spacer facing up).

The bottom line is that the mechanism engages with the ground only on the sole of the wheels, they act as a supporting system for the vehicle, which reduces energy losses, despite such drawbacks as the elasticity of the wheels and the loss of torque...

They are designed to be printed without supports, and are ready to assemble without additional post process. Dimensions: 241.5mm X 69,7 X 69,7 The lamp consist of two parts - lampshade and base, which are connected by Easy mount system with Neodymium...

The plug used in this instructions is waterproof.I use the panel to keep the LiPo battery in the irrigation system I built charged.Prints without supports, best printed in PETG. Tested in constant rain over days with success. Just be very careful...

Printing is to be done at 0.1 mm layer height with 0.2mm thickness (ideally using a 0,2mm nozzle), generating supports with an angle cap of 30 degrees. If printing everything in one go it is recommended to print at 80%&lt; infill, in order for...

setup I tought about is powerIn, lineIn and chaining)Included are the following push-in pieces:For powersocket 5,5mm (2,1mm Pin) external screwedFor powersocket 5,5mm (2,1mm Pin) internal screwedFor LineIn (jack) socket 3,5mm external screwedFor...

I hit the top of the steering tube with a nylon hammer while supporting the top and head tubes and nothing happened. I got that oh-shit feeling, like what is it going to take to disassemble this. After removing the stem spacers and the...

If You do not have a 16MHz crystal on hand, choose the proper MCU supported by Arduino IDE board definitions . Adjust the compiler settings this way. If in doubt set the fuses manually afterwards matching a newly generated hex-file. It runs at...

  This kit supports the following Oberth variant ship classes: #### [Oberth...

Re-worked heel piece a tad to get rid of a funny notch at the top between the pedal and supports. Added rounding to the outside/beneath edges of the boot. Rounded upper corners of the heel piece to match. Lined up the parts (one copy of each...

Entry panels, hatches, and more!No support requiredThe code and model files are using “Hatchbox” pla. ...Change if you are using something else (trying to use up what I bought a few months ago.)</li><li>Use variable height to smooth out the curves on...

The only parts requiring supports are the ATX power supply mount and the Z carriage (IIRC). List of changesZ-axisA Nema11 stepper with an integrated 5 mm / 2 mm pitch trapezoidal screw drives the z axis. The motion stage is guided by 4 mm rods and...

I have changed the wing supports, so wing now is held in place with elastic bands instead of glued. I hope I don't crash into the same rock again, but if I do, this time I don't want to glue the wings again. I have abandoned the brick and installed...