kobra go firmware 3d models

I usually have the initial layer horizontal expansion parameter in Cura set to -0.2 mm to prevent elephant's feet, but for the LEGO bricks with a default tolerance of 0.5 mm this must be reduced to -0.14 in order for the under-tubes to be printed on...

I was asked if it was possible to make it as a multiple GPU version and I decided to give it a go. The challenge lies in designing location and finding space for the PSU or PSU's. A super nice guy from CursedMining Discord Server "EmptyCarts" shipped...

I keep many of the tools I use for electronics projects stowed away in Stanley 014725R Organizer cases, so I made this solder fume extractor fan to go with them. This fume extractor is designed around a 60x60x25mm fan and a 10000mAh Lipo battery,...

The BBs will go in easily at first and become harder and harder as the bearing begins to be centered around them. Once you have the bearings in place, the hard work is done. Now get your Cams and insert each one into a slot in the Outer. Hold the Cam...

You're going to put the relay into the opening at a tilt and then roll it down into these protrusions to keep the relay in place. You need to strip off the power cable jacket to expose the wiring and you'll cut and install the black wire in to the...

[This is a US Based touch switch example](https://www.amazon.com/IKSACE-Capacitive-Control-Kitchen-Cabinet/dp/B08KDG1MZ5 "Example Touch Switch") [Here is an example on Aliexpress](https://www.aliexpress.com/item/32846782608.html "Aliexpress...

... may need support for the gear shafts, and the housing for the fan vent holes. Otherwise it's all print and install.Post-PrintingYou may need to adjust some of the part fitment to get it all to go together as each printer will vary. 

If you are familiar with programming this is effectively a GOTO command, making the program go to the beginning when it gets to the end. More info can be found <a href="https://marlinfw.org/docs/gcode/M808.html">here</a>. When saving the file to the...

Watch FBI: Most Wanted Season 1 Episode 2 Online Free Streaming, Watch FBI: Most Wanted Season 1 Episode 2 Online Full Streaming In HD Quality, Let's go see it. They soon joined four other Spider-Men from across the "Spider-Verse." Because all these...

The sliding part will go in next, and capture one end of the spring. Ideally the spring action of the slider should be moderate and should not take much force to move it in the track. I'd say the pressure of the slider should be similar to the...

The second time I ordered a print of the small STA coil with Shapeways it was flagged again for the same issues, but I could convince Shapeways again to go ahead and just print it as is, so don't be surprised when you get a bit of pushback when...

While my first pair have yet to break down, I've included an extra set without holes going completely through the spokes. Personally, I plan to upgrade to the ones without holes after these crack, but for now the absurdity of pointless embellishments...

The included button holder fits a 15 mm KCD11 switch.Bolts + nuts:M4x30 (4) to attach fan duct and motor housingM4 x 50 (4) to connect the handle halvesM3 x 6-ish (2) to connect the motor (I cut 10 mm ones)M3 x 10 (2) to attach the impeller to the...

You want to tighten the bolt to the point where the stepper cannot move anymore due to the increased friction and then go half a turn back. It is reccommended to put some grease/oil on the gears. The last configuration step is to set the right...

Please give it a go!https://www.thingiverse.com/thing:34198692018.10.16If you'd like to use my fang design with an Ender 3 printer, please try the mount plate that D3Dorsett created here: https://www.thingiverse.com/thing:31575972018.09.16I added an...

One is in black to match the junglecat controllers; and another one is Razer signature green color with a logo :-) Now I can just slide my phone in its existing case into the sleeve, slide the controllers onto the mounts, and it's ready to go. You...

Remember prizes go to the first few to show their makes so please post, like, and follow. If this proves popular, I will work on some other Dinosaurs and Prehistoric Creatures,as well as accessories and variants of this model if requested. I could...

You can import my slicer settings into Cura by going to Preferences &gt; Profiles &gt; Import and choosing the G-code file. Lithophane photo panels Choose a photo and crop it to a perfect square. I did this in Photos on Mac, but it could be done in...

Gradually tighten the four screws in turn, taking care not to misalign the lead nut, and secure the lead nut as far as it will go.  12. Check the quality of the Z...

...Be sure not to go too tight. Secure the lights to the printed stand. I used a figure 8 pattern to weave the lights down the tubes, however, I am considering putting the lights inside of the tubes to further eliminate any single point light sources.

Watch Emergence Season 1 Episode 11 Online Free Streaming, Watch Emergence Season 1 Episode 11 Online Full Streaming In HD Quality, Let's go to watch the latest series of your favorite series, Emergence Season 1 Episode 11. Come on join us!! What...

These components need to be connected directly, so that they don't bend away from each other, and cause the auger and the barrel to go out of alignment. (This makes even more thrust as the auger rubs against the wall of the barrel, bending them...

This is a remix of those elements from different sources. FreeCad source files included. Basically it's a printed 20x20 extrusion extending out at the rear end and another, taller one going vertical from there. On top there's a bow to hold the cable...

On the next version, I’m going to split the housing like an actual linear bearing to see if it improves on the vibrations. This slide will actually move over 25 lbs with the twin lead screw! If you have seen the previous Dovetail Stepper Slide, it...

This part won't print properly otherwise!For the mill top, I used zig zag supports for the large overhang on the bottom portion of the part.For the mill handle, I used tree supports, although you can probably get away without them in the orientation...

Bolt everything together, leave the doors on the side for now.Place the enclosure on the surface you are going to be using it, and start by marking down the back corner positions. Use double sided tape to secure the base parts. Now carefully place...

It can go out of sight easily. Rocksim says a C6-5 will take it to 1500 feet. Any wind at that altitude and your rocket is gone girl. The decals on the model (you can just see them in the picture) are made from cartoon stock on typewriter paper...

If I would do it again I'd go for 5mm magnets. They feel much nicer when placing together and also stack better vertically.</p><p>For a single tile (with my printer settings) you'll need:</p><ul><li>12 magnets</li><li>5,7g of filament for the...

Add a drop of ca glue on the knot on the wire and on the inner wall of the hole in the top disc (the one with the holes on the same side as the standing post will go in). Put the nut with the wire piece in a hole and put the plug in place. Press...

I only have one Mk4 to go off of and depend on information from the community to determine if there are any alignment issues or performance issues. ChangelogV1.0Initial ReleaseV1.1Added internal bridge to improve poor bridging characteristics on the...