meccano multi models 15 model set

You can find the CAD-file in the files section. There are many linear bearings variants here on thingiverse, and to give due credit I've copied the idea for the bushing from https://www.thingiverse.com/thing:2537701 Unfortunately I couldn't get the...

Update April 27, 2020 Added Version C8.1 with an optimized rubber band holder (Thanks to Corona-Hub-Vaihingen!) Update April 18, 2020 Added a stack of two frames (Thanks to Phillip Stinner!) This is a clear development from our first version of the...

*6 RTX ON keycap "esc" RTX ON (stl file) Update your design and your keyboard, with the gpu settings "RTX ON" put it and take more fps :P enjoy this. for mechanical keyboard with cherry buttons. *7 RTX GPU holder gpu GPU HOLDER (GRAPHICS CARD...

Nothing should require supports, though the cheesy NVidia logo will require a few mm of bridging and there are a few 45-degree overhangs, so set your fan speed high enough to accommodate this. Assemble the ears and segments using M4 screws, nuts and...

You can find 1102 with 4 holes motor mount if you want to stick to that size . Motors Suggestion :      Apex 1103 9999kv ✅     Hyperlite 1204.5 8022kv ✅     Xing Nano 1202 8000-10000kv ✅ ...

Majolica products were very expensive, which is why ordering a set of apothecary dishes emphasised the high economic status of the pharmacy owner. Grabowski’s collection includes: vessels (for liquid medicines), vases, jars (including albarella) and...

This is easier to set up if you remove the Y axis belt system first. Modify the frame as shown in the pictures so that the 45 degree angle of the frame is at 90 degrees to the front extrusions and spans the length of the extrusion (30mm) also make...

I was introduced to filament riveting in the "Articulated finger extensions" project by JulienJeanRoy https://www.thingiverse.com/thing:4342323 You use a soldering iron or wood working tool, set to the lowest temperature, and melt the end of a piece...

If you do, please post your remix! Other chainring clocks on Thingiverse Fahrrad Kettenblatt Wanduhr / Bicycle Chainring Clock by CBiker this one even has clock hands! Clock Housing 4 Chainrings 130mm by LukasQ Chainring Clock with support by...

The position of the air-blast tube is east to adjust with a single set screw to accommodate various focal lengths. This thing is also designed so that when fitted with a laser that has a 33x33mm cross section heatsink, the lens will be centered in...

You're also going to have to set new step/mm values for your extruder. It's usually very close to 320 steps/mm if you use the OEM extruder. If you're using the original stepper instead of a pancake stepper, you should also print the clearance...

Project details and a full list of credits here: https://www.designthatmatters.org/covid-19 Print instructions3d-printed headband in PLA, roughly 50g/1.75oz per part. Outer envelope of 3d-printed headband is 191mm wide, 148.5mm long, and 52.5mm...

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use. Taken from...

I have not tried this… you're on your own :)PrintingThe largest part (gantry) just fits on an MK3s bed - rotate until you have a fitPrint settings I used were slight tweaks on the MK3s 0.3mm layer Draft profile:3 perimeters5 top and bottom layers10%...

I did not rivet the nut in, my prints have turned out accurate enough the nut just taps in with a hammer and stays in place but you may have to open up the hole a little if it is too tight or glue it in if it is to...

Position its upper endpoint from the top of the constraint box and axis of symmetry and set its length as shown in the diagram.Connect the bottom endpoint of the vertical line to a diagonal line that ends on the vertical axis of symmetry. Adjust the...

Print Settings: Printer: Sintron Prusa i3 Rafts: No Leveling screws and springs are installed as usual. The belt clamp is just screwed under the owl using 4 M3x20 screws driven directly into the plastic. The holes in the carriage can also take a...

10cm 4Pin to 8 Pin EPS Power Supply Adapter Once all parts are in, I'll be making a full instruction set outlining everything from converting the Xbox One connector to powering on. It may take a few weeks, but if you already know enough about...

Print Settings Printer: Resolution: Infill: Notes: It may seem a bit counter-intuitive, but do not print this with supports. See the fifth bullet under Here's what I did in the summary above for an explanation. If you plan to use this as an actual...

Your luck may vary.No supports are required but make sure your bridging settings are tuned.Printed and tested in PLA+ but design should work in other non-TPU materials (PET/G, ABS, Nylon, etc.)There are 4 printed parts:Main body2 Legs1 Elastic Band...

Try to make multiple prints and experiment with settings until you get perfect (or almost) planetary gears for assembly. ## Parts list Parts to be printed : - 2 Planetary Gear A and B - Reducers support fixation * - Carrier - Insert C...

The tube can extend all the way to the extruder for a "reverse bowden". The spool holder is wide enough to hold any spools up to several kg, without needing any adjustments Spools are simply set on top of the curved rollers-- no rods to feed through,...

Some power supplies have an extra set of terminals, use those if you are lucky enough to have them. A little cable management, and you are done. I've included the OpenSCAD file so you can tweak it and clean up some of my quick and dirty code if you...

The Arduino Pro Micro is an ideal controller board for the scope of the project, it has plenty of pins, very easy to set up and a plug-and-play device, and has a lot of guides out there. I wanted to keep the vertical height of the unit as small...

With the carefully design inner structures, there is no need to activate the Vase Mode in Simplify3D; the careful design along with judicious positioning and slicer settings will give you clean parts without any unwanted oozing – as long as you...

I didn't get exact print times because I ran them overnight, but they are >10 hours with PLA at normal quality using the default settings for PLA in Luban. I designed the solution around mechanical parts I already had from a previous project. The...

I found, though, that I needed the air to go more horizontally to directly below the nozzle as the extruded filament wasn't always cooled quickly enough (I use a volcano set). So I made a version (version 2) duct with openings that are more...

-NITTY GRITTY DETAILS- To set up the holder properly, regardless of the intended viewing angle, users need to configure the power cable(s) to enter from the top of the board. This requires adjusting the default configuration and adding...

Depending on your printer, material and settings you may need to add support for the tongue that overhangs. If in doubt, add one backplate in PrusaSlicer, rotate 90°, cut off the tongue, rotate back and test print just that area.&nbsp;</p><figure...

Edit: Full screw list, as requested: * 10pcs of 412 CS + 4mm washers (2+2 for each upper mount to frame, 2+2 for nut mounts to X-bar, 2 for X-switch mount) * 8pcs of M312 BH + 3mm washers + locknuts for upper bearing mounts (2 per side) and nut to...