microscope phone attachment 3d models

-SOFTWARE- I'm going to be using a computer that has a docker instance of MotionEye on it, it's got a cheap 2tb HDD attached to it, so it should be able to record a few days footage at a time at full resolution. On the Pi itself, I'm going to be...

I'm still experimenting with the settings but right now I'm using: MaxSpeed 1000 Acceleration 50 Speed 300 I then run the motor 800 steps forward followed by 5000 steps in reverse to dispense. Attached is a small sketch I use for testing that just...

In addition, I have a holder for the ESP32 designed this can be inserted there and attached with some of the double-sided adhesive tape.“Power Supply”: The Power Supply Enclosure must be printed with supports“Cylinder inside”: The cylinder...

The 3D printing figurine's chosen scale is 1:250 for the FFF/FDM version and 1:500 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 88 parts;- A printed model is 535 mm tall, 431 mm wide, 852 mm deep;- The...

Case Parts Requirements ==================== Parts for Assembly: ---------------- - 28mm x 3mm piano wire, 8 pieces - Glue (optional, secure wire in sides) - M3 screw inserts, holes are sized for Ruthex threaded inserts - M3x8 screw, 5 - M3x20...

Attach to the battery [like this](https://imgur.com/a/QDmiEqw) to keep the quad balanced. * Prop guards: CF Nylon or PETG, 2 walls, 50% octet infill. STL is for the right prop guard, just mirror it before printing to make the left guard. I use...

(This was done due to Fusion 360 repeatedly failing to properly combine the parts to allow them to be exported as an STL for printing.) Materials NeededWhat you need: Printed one of the three provided files (RECOMENDED reinforced_holes.stl Pictured:...

The STL filenames have both the style (normal/thin/wide) and the inner diameter in mm in the filename.In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your...

This powerful LED fixture comes attached to a tripod mount that allows operators to easily place this unit in the desired location within the workplace or job site.*PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY*The EPL-QC-QP-1X150LED-RT-100-EPP...

3) Tried 2) with a 7 bar attached to the leg of the T and two studs on each side. This was okay but the bars kept pulling forward making the mask loose-ish. I only had the T's loosely stuck in the head band so they could wiggle (not good). Will...

Use attached 3MF project file. Otherwise you manually have to split the included STL files in their parts and assign colors to the parts.&nbsp;</li><li>Use some brim if printing in PLA. Printing in PETG worked for me without any...

Work plane• 1 x Ikea Sysselsätta cutting board https://www.ikea.com/fi/fi/p/sysselsaetta-leikkuulauta-30359016/• 1 x Telescopic drawer support https://www.biltema.fi/rakentaminen/saranat/erikoissaranat/teleskooppikannattimet-2-kpl-2000018627• Lack...

The 3D printing figurine's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 11 parts;- A printed model is 250 mm tall, 119 mm wide, 118 mm deep;- The...

| | remora-secondary-hull.stl | Secondary hull to which all other components attach. | | thufir-main-hull.stl | Combined saucer and secondary hull. | | thufir-nacelle-port.stl |...

Download the OpenSCAD model from the floor stand model.If you could take a picture of an actual print, please "comment" and attach the picture. - I am curious to see your uses in the wild!</strong></i></p><p>This design is very very similar to his...

The 3D printing figurine's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 12 parts;- A printed model is 244 mm tall, 144 mm wide, 99 mm deep;- The...

ABOUT THIS 3D MODELThe Galileo II (NCC-1701⁄7) was a Federation shuttlecraft attached to the legendary USS Enterprise. Trekkies and classic sci-fi fans alike have voiced their appreciation for the simple and neat craft and even tried recreating it in...

The motion of the Slide moves the Hammer via small bosses in the Slide, keeping the Rotor free to turn. The Rotor is the square notch style from the bakewell remix, to which I added a flange on both sides to keep it centered in the Slide. Changed the...

if it will be on a table or desk Printing If you will be printing the 'rotated' version, refer to the 'Code changes' section (above) to make the necessary code change and upload it to the Arduino. You will need to print 3 parts; a front, a rear and...

are provided as separate assembly parts.All assembly parts of the FFF/FDM versions come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing...

The 3D printing figurine's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 33 parts;- A printed model is 290 mm tall, 156 mm wide, 266 mm deep;- The...

The 3D printing figurine's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 17 parts;- A printed model is 300 mm tall, 182 mm wide, 174 mm deep;- The...

The 3D printing figurine's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM Pose 1 & Pose 2 1.0 versions features:- You can choose between Pose 1 and Pose 2 designs;- Contain 27 parts...

This is a five colour print, but you don't need any special printer accessories like an MMU to print this, just a lot of setup in PrusaSlicer.I've attached the 3MF file I ended up with, so you can use that and skip the rest of this setup if you...

(new board)Use double-sided tape to attach the charging board to the hull.Solder all cables on the motor controller board then protect it with heat shrink tube(16mm) or electrical tape.Assemble the left chassis and insert the motor and zip...

Minimum Build ------------------- At the very least, you need the following parts: * 1x 4-Way_Planting_Module_Hollow_Twist.STL * 1x Dispenser_Module_Internal.STL * 1x Filling_Cap.STL * 1x Filling_Cap_Symbol.STL * 3x IKEA_Muskot_24cm_Petal.STL * 1x...

Take the worm gear and the 5mm shaft, and epoxy the shaft inside the worm gear making sure to install it in the lower half of the worm (specifically not the part with the setscrew) it is critical that this shaft be aligned parallel with the worm...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 37 parts;- A printed model is 299 mm tall, 223 mm wide, 204 mm deep;-...

The 3D printing figurine's chosen scale is 1/2 for the FFF/FDM version and 1/4 for the DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 18 parts;- A printed model is 283 mm tall, 237 mm wide, 198 mm deep​;- Comes...

Parts of arrows you can print separately;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version features:- Contains 14 parts;- A printed model is 235 mm tall, 98 mm wide, 135...