rectangular desk grommet 3d models

My sand spirograph brings math from your school desk to the beach. About the design: Modelled in Blender with the original Spirograph toy in mind that I used to have when I was little, taking inspiration from my childhood memories. I aimed to keep...

Not because I think it is final, but because it will serve as an inspiration sitting on my desk.\r\n\r\nPlease feel free to comment positively. Please bear in mind this will not be a scale model, I just look at photos of the Peterbilt 359 and make...

My engraver is on a desk adjoining my main work area and this thing keeps casual glances and passing family from getting the full impact of reflected laser energy. Always wear your safety glasses when dealing with lasers! All that being said, the...

I found that if I ran a small desk fan pointed down beside the printer near the PSU, the cooling was sufficient and the PSU didn't even get warm. This solution worked, but wasn't elegant, so I set out to remount the PSU vertically behind the z...

I run two Dell Optiplex 3060 mini micro PC's for my Home Lab.I wanted something compact to consolidate desk space and at the same time help to cool the PC's by creating a case for everything, including a low noise 120mm cooling fan that is 12v...

A stand to store your Wowstick and bits on your desk. This is a from scratch redesign in Fusion 360 of the original thing:2893136 by vanilla_thunder and the previous remix thing:3085888 that I did. The original source design by vanilla_thunder was...

I found myself using a very small rubber-handled screwdriver as a light mallet when getting the snap-fit parts to seat well, setting the body on my desk, positioning the roof and gently tapping the pegs into place. Same with the cow catchers,...

Recommended print resolutions: Tower Quadrants: 0.3mm roofParkHalves: 0.2mm treesVentsEtc: 0.1mm These units are, or provide, over a tent or other temporary shelter: - Dry and Warm (Forced Air/Heat) - Safe and Secure (Strong Theft/Assault...

This avoids the big pot getting old and you have hand cream immediately available when your hands start to become dry, which is always a problem around here in winter times. I have one of these little containers on my home office desk for many...

It may take some minimal filing depending on the size of the "elephants foot" from the bed adhesion.2: Mount the bottom piece to the fan with four M3 bolts.3: Using a new surgical mask, streatch it over the bottom piece and carefully place the...

Do not place the sensor on a desk, humans breathing out CO2, an thus elevating the displayed 'average' CO2 level in the room prematurely.https://operame.nl/HardwareSoftwareOpen source, see https://operame.nl/SoftwareThe software user-interface is...

These gadgets are super popular gag gifts that make for great desk toys! You can print this one yourself, and the parts are incredibly cheap. Check out the instructions for a comprehensive list of components and assembly steps. One is for the...

This one attempts to be meta-puzzle art but for sure at least succeeds as doubling as a desk pen holder. In order to most-efficiently meet all my goals, with me being a software engineer by trade, I wrote a dirty Java app to read in an image, spit...

I used super glue to hold the magnets in place, letting them dry whilst the two covers were lined up together (top cover on the desk with the exposed holes, bottom cover on top of that). Only two magnets in opposite corners are needed, but I included...

To finish, I got some liquid rubber (Dipit) at the hardware store and coated the bottom of the frame; so it would stick to, and not slip on a desk or tabletop surface. You can seal the ends of the rod so the support S curves don't come apart as...

... B outputs (not super important, but you can always change them in the software) You need to remove the LED. It's a good idea to add something non-slippery to the bottom so you can rotate the knob easily. Pure PLA is too slippery on desk surfaces.

Prusa MMU 2.0 Filament Control for Lack Enclosure I needed to control the loading/unloading of filaments for my Prusa Multi-Material 2.0, and it had to be compact and fit below my Ikea Lack enclosure on my desk to be fed by an airtight box. I was...

To remove an extra cable from my desk, I integrated a Raspberry Pi 3B with Octoprint inside the case, along with a Sonoff switch to remotely turn on and off the printer. On the PSU, I installed a 60mm silent fan (the original one was noisy),...

DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 The good thing about this design so far is the stepper motor float over the desk, better...

I adore vintage flexible desk lamps. So I decided to create a similar styled holder for my Kindle. Now, I know what you're thinking, they are not that heavy, but when I'm in bed, I struggle to get my neck around to read it when it's on my chest. At...

What I did for the bottom was rotate my printer so the case hung off my desk, then screwed in bottom screws. Optional - I put felt pads on the bottom of my case to make clearance for screws. Sometimes, I don't even screw in the bottom. ### Screws 6...

If there is interest I can come up with a design that the letters run all horizontal and therefor could sit on a desk. Print the "Housings" with the back on the build plate and with 5 perimeters so they are solid. I haven't arranged the models in...

It is about 1mm thicker than the protruding lenses so the glass on the lenses do not touch the surface when the phone is sitting on a desk, for example. Like most of my prints here, I designed this for myself. But it fits nicely so I thought that I...

Do you love science, do you love CERN, have you ever wanted your very own part of the ATLAS experiment to call your very own, a Muon Spectrometer you can print, build and awkwardly place on your desk? One you can call your very own.</p> <p>Well...

This project combines our Crystal Generator and Arduino Nano NeoPixel Ring Base projects to create a glowing desk lamp. In this project we've provided the STL files you'll need. They are exports from the aforementioned projects. Please see the...

These are sleek desktop satellite speakers, they have a very small foot print, but are tall enough to stand above desk-top clutter. Twin Tectonic BMR 28mm drivers give excellent dispersion, and the twin 65mm passive radiators give bass response down...

Sherm Check out some of my other projects on Thingiverse: * Locking Stone Box: https://www.thingiverse.com/thing:2875966 * Solar Light house: https://www.thingiverse.com/thing:2875991 * Hida a key flag holder:...

DELTA PIPE PRINTER (DPP) Please refer to the DELTA PIPE PRINTER STEP 1 TOP FRAME for additional references and instructions http://www.thingiverse.com/thing:1344167 The good thing about this design so far is that the stepper motor floats above the...

Mount the original feet on the bottom to keep it from sliding on my desk.Parts &amp; InstallationBesides printing 2 legs, you just need 2 M3x6mm screws. If you get socket head screws (like those in <a...

There is an online repository with CAD, STL, and STEP files available at https://github.com/jonbitzen/cable-organizerLicense CC BY-NC-SAChanges and Featureschanged hinge joint tolerance to 0.4 mm, allows the arm snap to close more tightlybasic...